Shop headings: New Spares | Used Spares | Accessories | Brands
Dimensions:
M10 conventional thread, approx. 240mm reach to far edge of mirror, mirror 110mm diameter
Black handlebar mounted mirror. Conventional M10 thread, head is threaded for left or right hand fitment.
Supercedes BUMM mirror HAA36021W. See ACA00101 for a black mirror extender kit to extend the reach of this mirror.
4 in stock
£18.00
INC VAT
£15.00 EX VAT
Ninety degree angle extender for schrader tyre valves. Improves access to valve for tyre pressure checking
Suitable for 130/70 x 17, 140/70 x 17, 130/80 x 70, 120/90 x 17 tyres
4 in stock
£5.50
INC VAT
£4.58 EX VAT
Kit consisting of black plastic cap and rubber cap seal for PS 12 round handlebar master cylinders and single horizontal outlet remote reservoirs (e.g. BRG19901 )
Also known as Guzzi ref. 17661052, 10271110. Brembo ref. 110430830. This is the smaller of the two round master cylinder caps used on V35, V50, V65 and 850/1000 models
3 in stock
10430830 GU10430830 10 43 08 30
1043 0830 1043.0830 10.43.08.30
Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei
£12.00
INC VAT
£10.00 EX VAT
Rebuild kit for Brembo PS 13 handlebar mounted brake and clutch master cylinders, includes all seals, return spring and brake grease. Piston is hollow
This seal kit is for Cali 1100 master cylinders with a hollow pivot pin, does not fit early models with a solid pivot pin. For Cali EV models this only fits master cylinders with a pair of screws in the middle of the cap, it does not fit the later master cylinder which has diagonally opposed screws. Also know as Guzzi ref. 28659378, 000043851, 30659330. NB Included instructions may refer to rear master cylinder applications rather than front. Brembo ref. 110436250
3 in stock
Also fits Cagiva Elefant E750, Ducati 748
£26.00
INC VAT
£21.67 EX VAT
Lower right hand choke cable for carb models
We advise you to measure your existing cable before ordering in case you have a non standard set up.
3 in stock
30133560 GU30133560 30 13 35 60
3013 3560 3013.3560 30.13.35.60
£6.60
INC VAT
£5.50 EX VAT
Nut for clutch centre gear CLA30810, fits on gearbox input shaft
See TOA14903 for special tool
3 in stock
93601022-z 93601022 GU93601022 93 60 10 22
9360 1022 9360.1022 93.60.10.22
£10.00
INC VAT
£8.33 EX VAT
Zadi ignition switch with 2 keys
4 male spade type connectors on underside, replaces original switch with bullet connectors. See ELA10005 for female spade connectors and FRA19741 for rubber wiring boot
3 in stock
31735360 GU31735360 31 73 53 60
3173 5360 3173.5360 31.73.53.60
Also fits Benelli 750 Sei (series 2) - fits with minor modification
£31.00
INC VAT
£25.83 EX VAT
4 pin female block connector used for main loom connections. See ELA17603 for the Molex connectors that go in this block. Use male molex connectors with this block
3 in stock
£2.30
INC VAT
£1.92 EX VAT
12 pin male block connector, used for main loom connections. See ELA17738 for the Molex connectors that go in this block. Use female molex connectors with this block
NB this connector has one zigzag end
3 in stock
£3.60
INC VAT
£3.00 EX VAT
15 pin female block connector, used for main loom connections. See ELA17603 for the Molex connectors that go in this block. Use male molex connectors with this block
NB this connector has one zigzag end
3 in stock
£4.20
INC VAT
£3.50 EX VAT