Shop headings: New Spares | Used Spares | Accessories | Brands
Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.
This part is available by special order, request a quote
£175.00
INC VAT
£145.83 EX VAT
Polished aluminium clutch lever without master cylinder rod. You will need to remove the operating rod from your old clutch lever (loosen grub screws to remove)
Also known as Guzzi ref. 981046
This part is due back in stock soon, call 01484 841395 to reserve yours
AP8118659
£30.00
INC VAT
£25.00 EX VAT
Replacement clutch plate for single plate RAM clutches
Torque setting for fitting this is 25Nm with a thread locking compound
This part is available by special order, request a quote
£146.00
INC VAT
£121.67 EX VAT
Clutch master cylinder cap and rubber kit for Brembo PSC 12/25 master cylinder
Brembo ref. 110270446
This part is available by special order, request a quote
AP8113997
£63.00
INC VAT
£52.50 EX VAT
M8 wavy washer
Also known as a crinkle washer
This part is due back in stock soon, call 01484 841395 to reserve yours
£0.30
INC VAT
£0.25 EX VAT
Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use
Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool
This part is available by special order, request a quote
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£70.00
INC VAT
£58.33 EX VAT
Clutch pushrod
This part is available by special order, request a quote
05085730 GU05085730 05 08 57 30
0508 5730 0508.5730 05.08.57.30
£22.80
INC VAT
£19.00 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
This part is due back in stock soon, call 01484 841395 to reserve yours
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates
Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes
This part is due back in stock soon, call 01484 841395 to reserve yours
30906510 GU30906510 30 90 65 10
3090 6510 3090.6510 30.90.65.10
£110.00
INC VAT
£91.67 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
This part is due back in stock soon, call 01484 841395 to reserve yours
£186.50
INC VAT
£155.42 EX VAT