3 pin plastic connector for headlight bulb spade connections

No longer available from Guzzi

 Sorry, this part is no longer available.

 17740364 GU17740364 17 74 03 64
 1774 0364 1774.0364 17.74.03.64

Alternator stator for Bosch charging systems, this does not include the plate and brush holders

To fit this you will need to solder in the three wires from the windings. Replacement rotors and brushes also available. See ELA00503 for a complete higher output upgrade for your charging system

 This part is available by special order, request a quote

 17712400 GU17712400 17 71 24 00
 1771 2400 1771.2400 17.71.24.00

Brush holder for Bosch alternator stator

Also known as Guzzi ref. 17712454, 14712452

Includes brushes. See ELA17453

 This part is due back in stock soon, call 01484 841395 to reserve yours

 17712452 GU17712452 17 71 24 52
 1771 2452 1771.2452 17.71.24.52

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Regulator rectifier for Saprisa charging systems

Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part. The standard black block connector is not compatible with the updated 7 pin reg/rec, you will instead need to fit female spade connectors to your wires.

 This part is due back in stock soon, call 01484 841395 to reserve yours

28703800-z 28703800 GU28703800 28 70 38 00
 2870 3800 2870.3800 28.70.38.00

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

NE5

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Neutral indicator switch

 Availability varies on this part, check availability

 12207200 GU12207200 12 20 72 00
 1220 7200 1220.7200 12.20.72.00

Marelli condenser with cable and mount bracket

2 required

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14715433 GU14715433 14 71 54 33
 1471 5433 1471.5433 14.71.54.33