Long screw in polished alloy thermometer dipstick with O ring for models with a sump extension. Shows oil temperature in degrees celcius

Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick

 This part is due back in stock soon, call 01484 841395 to reserve yours

28004950-z 28004950 GU28004950 28 00 49 50
 2800 4950 2800.4950 28.00.49.50

Short screw in polished alloy thermometer dipstick with O ring for models without a sump extension. Shows oil temperature in degrees celcius

Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick

 This part is available by special order, request a quote

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51

Stainless steel braided hose oil pipes for head to crankcase connection. Replaces leak prone rubber pipes. Includes V shaped banjo.

Always replace crush washers (6 x SIA12200) when fitting new oil lines, you may also require three of our banjo bolts ENA95990

 3 in stock

 14153601 GU14153601 14 15 36 01
 1415 3601 1415.3601 14.15.36.01

Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)

Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings

 This part is available by special order, request a quote

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 1 in stock

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Uprated double row cam chain, ideally fit with sprung chain tensioner ENA20071

 This part is due back in stock soon, call 01484 841395 to reserve yours

 28058060 GU28058060 28 05 80 60
 2805 8060 2805.8060 28.05.80.60

Stainless steel braided hose oil lines for heads on square barrel models. See ENA14662 if you also need threaded link to cylinder head

Always replace crush washers (SIA12200 x 2 and SIA10900 x 2) when replacing oil lines, you may also require our banjo bolt ENA95990. Also known as Guzzi ref. 01153600 and 01153602

 3 in stock

 14153660 GU14153660 14 15 36 60
 1415 3660 1415.3660 14.15.36.60

Pair of chrome tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 This part is due back in stock soon, call 01484 841395 to reserve yours

Complete high quality gasket kit for round barrel 850 models

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12 x ENA97624 and 2 x ENA90203

 This part is due back in stock soon, call 01484 841395 to reserve yours

17999050-z 17999050 GU17999050 17 99 90 50
 1799 9050 1799.9050 17.99.90.50

Complete gasket kit for all square barrel 1000 models

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12x ENA97624 and 2 x ENA90203

 This part is due back in stock soon, call 01484 841395 to reserve yours

29999000-z 29999000 GU29999000 29 99 90 00
 2999 9000 2999.9000 29.99.90.00