Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77
Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit
More than 5 in stock
14939950 GU14939950 14 93 99 50
1493 9950 1493.9950 14.93.99.50
Also fits Hesketh, Laverda
£18.75
INC VAT
£15.62 EX VAT
Air filter, cylindrical paper cartridge type
See SIA10422 for a reusable K & N air filter
More than 5 in stock
AP8104211
£11.70
INC VAT
£9.75 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
Silencer clamp gasket / shim or muffler gasket used to seal crossover to silencer
This exhaust bush is not required if a Mistral or Agostini silencer is fitted
1 in stock
05128230 GU05128230 05 12 82 30
0512 8230 0512.8230 05.12.82.30
£25.00
INC VAT
£20.83 EX VAT
Head Gasket
5 in stock
30022060 GU30022060 30 02 20 60
3002 2060 3002.2060 30.02.20.60
£14.40
INC VAT
£12.00 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT
Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems
These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt
More than 5 in stock
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT