Complete Speedo (odometer) cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 4 in stock

14760450-z 14760450 GU14760450 14 76 04 50
 1476 0450 1476.0450 14.76.04.50

Manual left hand petrol tap with nut. On, Off and Reserve settings.

Will also fit most other Moto Guzzi tanks from 1976 to 1991, these can be used to replace discontinued electric taps but please measure first and check you have space for outlet pipe

 More than 5 in stock

65105400-z 65105400 GU65105400 65 10 54 00
 6510 5400 6510.5400 65.10.54.00

Also fits Laverda Jota. Can be used on Morini 350 Sport and Morini 350 Strada as replacement for electronic fuel tap

Sebac fork damper, standard damping rate

See OIA01001 for ATF (used in place of fork oil)

 3 in stock

14526407-z 14526407 GU14526407 14 52 64 07
 1452 6407 1452.6407 14.52.64.07

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 1 in stock

Carb gasket kit / rebuild kit for Dellorto VHB29, VHB30, VHB24 and VHB26 carbs

Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit. As this kit is intended for several different carbs you may have gaskets or O rings remaining after rebuilding. More information on rebuilding your VHB carb can be found here.

 More than 5 in stock

 17939950 GU17939950 17 93 99 50
 1793 9950 1793.9950 17.93.99.50

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Carb gasket kit / rebuild kit for Dellorto VHB29, VHB30, VHB24 and VHB26 carbs

Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit. As this kit is intended for several different carbs you may have gaskets or O rings remaining after rebuilding. More information on rebuilding your VHB carb can be found here.

 More than 5 in stock

 17939950 GU17939950 17 93 99 50
 1793 9950 1793.9950 17.93.99.50

Pair of universal Domino chromed handlebars, medium rise.

Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps - see dimensions if in doubt about suitability for your bike

 1 in stock

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

 More than 5 in stock

 14153000 GU14153000 14 15 30 00
 1415 3000 1415.3000 14.15.30.00