Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Reproduction chain tensioner for rear wheel spindle. The axle passes through the head of this chain adjuster
This part is available by special order, request a quote
10336300-z 10336300 GU10336300 10 33 63 00
1033 6300 1033.6300 10.33.63.00
£44.00
INC VAT
£36.67 EX VAT
Pair of EBC FA047 sintered brake pads for Brembo F05 (P5) and Grimeca calipers for extra braking power
Fits Nevada up until frame no. LK112433 Fits all calipers on pre 1993 models
2 in stock
27654610-z 27654610 GU27654610 27 65 46 10
2765 4610 2765.4610 27.65.46.10
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT
Front crank oil seal for models with Bosch or Ducati charging systems
Also known as Guzz ref. 90402839
More than 5 in stock
90402840-Z
£9.50
INC VAT
£7.92 EX VAT
Stainless steel braided hose oil pipes for head to crankcase connection. Replaces leak prone rubber pipes. Includes V shaped banjo.
Always replace crush washers (6 x SIA12200) when fitting new oil lines, you may also require three of our banjo bolts ENA95990
This part is due back in stock soon, call 01484 841395 to reserve yours
14153601 GU14153601 14 15 36 01
1415 3601 1415.3601 14.15.36.01
£62.00
INC VAT
£51.67 EX VAT
Lower Throttle cable
This runs from the splitter to the carb. We advise you to measure your existing cable before ordering in case you have a non standard set up.
Sorry, this part is no longer available.
31117715 GU31117715 31 11 77 15
3111 7715 3111.7715 31.11.77.15
Sorry this item is out of production
Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.
This part is available by special order, request a quote
£465.00
INC VAT
£387.50 EX VAT
Smarten up the rear of your V7 with this fenda eliminator kit with includes an LED tail light.
This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks
1 in stock
£185.20
INC VAT
£154.33 EX VAT