Stainless steel exhaust cover for the exhaust link pipe and CAT. Fits easily to the standard exhaust system to improve the styling of the V100. This brushed stainless finish cover also helps shield your feet from the heat of the CAT. Note that this accessory is not compatible with a centre stand.

A quality accessory hand made in Italy for your V100

 This part is due back in stock soon, call 01484 841395 to reserve yours

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10433 and V-Twin Boost - ACA85001 or ACA85002.

Customer Kev fitted this combo and called us the next day to say that his V85TT was transformed; the fluffy throttle response between 2k and 3k was gone and the engine pulled better. Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Pair of open ended black rubber handlebar grips to replace standard fitment

 Sorry, this part is no longer available.

 03603560 GU03603560 03 60 35 60
 0360 3560 0360.3560 03.60.35.60

Plastic inlet manifold, replaces unavailable aluminium manifold. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. PHF36 carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts

 This part is available by special order, request a quote

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters

 1 in stock

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHM 40 carb conversions on models previously fitted with smaller carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts

 This part is available by special order, request a quote

Full workshop manual for 4 valve Griso 1200 models covering maintenance, overhaul and detailed repair

Includes tolerances for many parts. This is a comb bound reprint

 1 in stock

 854378 MG854378

Guzzi Factory Workshop Manual for Breva 750. 280 pages covering the basics or maintenance and rebuilding for the Breva 750. Includes sections on technical specifications, maintenance, fuel system, engine, gearbox, transmission, electrics, cycle parts and chassis

Includes basic test data for electrical parts including TPS

 1 in stock

Round plastic bulb holder for instrument warning lights.

Supercedes Guzzi ref. 10754905. For bulb LIA93140

 3 in stock

 19768680 GU19768680 19 76 86 80
 1976 8680 1976.8680 19.76.86.80

Complete rear brake disc, 6 hole mounting. Made by EBC

Always replace brake pads when fitting new brake discs, see BRA05630 for brake pads. Compatible with ABS equipped bikes. Also known as Guzzi ref. 85227R. Needs 6 brake disc bolts BRA30460

 Order now and we will post your order within 7 days.

 05635730 GU05635730 05 63 57 30
 0563 5730 0563.5730 05.63.57.30