High rise chromed handlebars with cross brace
These can be fitted to pre 1979 models but you will need to drill the bars to allow switchgear wiring to be correctly routed through the handlebars
This part is available by special order, request a quote
17600270 GU17600270 17 60 02 70
1760 0270 1760.0270 17.60.02.70
£75.00
INC VAT
£62.50 EX VAT
Manual square bodied fuel tap with nut, washer and filter. Fits left or right hand side of tank.
Off, on and reserve positions. Approved for use with fuel containing ethanol.
2 in stock
14105400-z 14105400 GU14105400 14 10 54 00
1410 5400 1410.5400 14.10.54.00
£40.00
INC VAT
£33.33 EX VAT
This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.
Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.
See installation instructions here.
This part is available by special order, request a quote
£149.00
INC VAT
£124.17 EX VAT
Pair of EBC FA047 sintered brake pads for Brembo F05 (P5) and Grimeca calipers for extra braking power
Fits Nevada up until frame no. LK112433 Fits all calipers on pre 1993 models
2 in stock
27654610-z 27654610 GU27654610 27 65 46 10
2765 4610 2765.4610 27.65.46.10
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT
Front crank oil seal for models with Bosch or Ducati charging systems
Also known as Guzz ref. 90402839
More than 5 in stock
90402840-Z
£9.50
INC VAT
£7.92 EX VAT
Stainless steel braided hose oil pipes for head to crankcase connection. Replaces leak prone rubber pipes. Includes V shaped banjo.
Always replace crush washers (6 x SIA12200) when fitting new oil lines, you may also require three of our banjo bolts ENA95990
This part is due back in stock soon, call 01484 841395 to reserve yours
14153601 GU14153601 14 15 36 01
1415 3601 1415.3601 14.15.36.01
£62.00
INC VAT
£51.67 EX VAT
Lower Throttle cable
This runs from the splitter to the carb. We advise you to measure your existing cable before ordering in case you have a non standard set up.
Sorry, this part is no longer available.
31117715 GU31117715 31 11 77 15
3111 7715 3111.7715 31.11.77.15
Sorry this item is out of production
Smarten up the rear of your V7 with this fenda eliminator kit with includes an LED tail light.
This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks
2 in stock
£185.20
INC VAT
£154.33 EX VAT
Full workshop manual for Cali EV models covering maintenance, overhaul and detailed repair
Includes tolerances for many parts. This is a bound reprint in English which also covers models equipped with hydraulic tappets (PI models)
Order now and we will post your order within 7 days.
£27.50
(VAT exempt)
£27.50 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
1 in stock
£186.50
INC VAT
£155.42 EX VAT