Shop headings: New Spares | Used Spares | Accessories | Brands
Rear hugger finished in gloss black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets
Supplied with brackets, stainless fasteners and fitting instructions
Sorry, this part is no longer available.
Sorry this item is out of production
Stylish guard to protect your centre stand from damage. This beautifully made part is manufactured from stainless steel plate for maximum protection and longevity. Drilled to save weight this is an essential accessory if you take your Stelvio off road
Sorry, this part is no longer available.
Sorry this item is out of production
Lighter flywheel (2.2kg) for dual plate clutch, this will improve acceleration, engine pickup and gear shifts
This part is available by special order, request a quote
04067000 GU04067000 04 06 70 00
0406 7000 0406.7000 04.06.70.00
£695.00
INC VAT
£579.17 EX VAT
Deep sump spacer made from alloy. This increases the volume of air in the crankcase and helps reduce 'heavy breathing'. The oil is also better cooled when using one of these. Finished externally in silver paint
To fit this sump spacer you will need longer sump bolts (14 x SSA06055 + 4 x SSA06090) and a pair of sump gaskets (ENA14036). You will also need a longer dipstick, see ENA28005
Availability varies on this part, check availability
14003240 GU14003240 14 00 32 40
1400 3240 1400.3240 14.00.32.40
£128.00
INC VAT
£106.67 EX VAT
Short screw in polished alloy dipstick with O ring for models without a sump extension. Can be used to replace long dipstick and tube on Le Mans 2 and 1000 SP
Will also fit V7 700, V7 Special and 850 GT if high and low levels are transposed from your old dipstick
This part is due back in stock soon, call 01484 841395 to reserve yours
17004951-z 17004951 GU17004951 17 00 49 51
1700 4951 1700.4951 17.00.49.51
£21.00
INC VAT
£17.50 EX VAT
Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression
Components for one cylinder. This kit can be fitted to a 850 crankcase if the crankcase aperture is enlarged. See similar kit ENA20050 for alternative
Sorry, this part is no longer available.
18060102-z 18060102 GU18060102 18 06 01 02
1806 0102 1806.0102 18.06.01.02
Sorry this item is out of production
Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers
This part is due back in stock soon, call 01484 841395 to reserve yours
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£24.30
INC VAT
£20.25 EX VAT
Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)
Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings
This part is available by special order, request a quote
£59.50
INC VAT
£49.58 EX VAT
Long screw in polished alloy thermometer dipstick with O ring for models with a sump extension. Shows oil temperature in degrees celcius
Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick
This part is due back in stock soon, call 01484 841395 to reserve yours
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£70.00
INC VAT
£58.33 EX VAT
Screw in polished alloy thermometer dipstick with O ring. Shows oil temperature in degrees celcius
Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick
This part is due back in stock soon, call 01484 841395 to reserve yours
£70.00
INC VAT
£58.33 EX VAT