Long screw in polished alloy dipstick with O ring. Will not fit later 4v/cylinder models that have unthreaded dipstick

1 in stock

01004900-z 01004900 GU01004900 01 00 49 00
 0100 4900 0100.4900 01.00.49.00

Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)

Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings

Short screw in polished alloy dipstick with O ring for models without a sump extension. Can be used to replace long dipstick and tube on Le Mans 2 and 1000 SP

Will also fit V7 700, V7 Special and 850 GT if high and low levels are transposed from your old dipstick

1 in stock

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51

Polished aluminium blanking plate kit, use when fitting a crankshaft mounted ignition to replace the distributor

Includes O ring and two countersunk screws

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

1 in stock

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Protection bar for bikes rear drive box or bevel box. Protects against expensive damage

Save your leg with a dynastart electric start

You may also need a new drive pulley for a 17mm OD shaft, a longer mounting bolt, starter switch and relay

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

Stainless steel fasteners kit for VHB carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

More than 5 in stock