Rubber brakelight switch cover, 90 Degree

Also known as Guzzi ref. 10352710

12735100-z 12735100 GU12735100 12 73 51 00
 1273 5100 1273.5100 12.73.51.00

Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems

These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt

Also fits Benelli 250 TS

Dimensions:
M10 x 1

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

Dimensions:
49cm x 5mm x 8mm

M12 pivot bolt kit for brake and gear lever pivots on Tonti framed models. Kit consists of 1 M12 bolt (with hex head and slotted other end), wavy washer, flat washer and half nut

Beautifully made to enhance the appearance of your bike, also cheaper than OE non stainless parts. Guzzi parts refs: 30252360, 98073660, 95100409, 92701120, 17252350. Does not fit G5

98053660-z 98053660 GU98053660 98 05 36 60
 9805 3660 9805.3660 98.05.36.60

Dimensions:
M12

Brembo rubber bleed nipple cap without retaining ring

Dimensions:
11mm overall height

Zinc finish brake disc bolt, pre-treated with thread locking compound.

98230825-z 98230825 GU98230825 98 23 08 25
 9823 0825 9823.0825 98.23.08.25

Pad pin kit for rear brake caliper. Consists of pad pin plus split pin

Also known as Guzzi ref. 978606

 05659130 GU05659130 05 65 91 30
 0565 9130 0565.9130 05.65.91.30

Dimensions:
Pin 58mm long

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover
  
   2 in stock

  Dimensions:
  M10 bolt with M6 bleed nipple

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Pair of EBC FA209 semi-sintered brake pads, used for front brake pads on Quota and Bellagio, rear brake pads for V100, Cali 1400, Cali EV, Cali Stone, Cali Jackal and Special. All use Brembo PF2.3032 caliper

Choose these semi-sintered brake pads if you are looking for extra braking performance. Also known as Guzzi ref. 30654626, AP8113627

 03654600 GU03654600 03 65 46 00
 0365 4600 0365.4600 03.65.46.00

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

Dimensions:
M10 single banjo fine thread