Stainless steel drain plug for drive box and gearbox, includes recess for crush washer to locate in. Also used as level plug on big twins and front sump drain on small twins.

Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt

95980214-z 95980214 GU95980214 95 98 02 14
 9598 0214 9598.0214 95.98.02.14

Dimensions:
M10

A2 Stainless steel M5 socket cap screw, many uses including as long screw retaining filler cap, 3 required on 1100 Sport, Daytona and V11 Sport

Replaces Guzzi ref. AP8150453

 98690230 GU98690230 98 69 02 30
 9869 0230 9869.0230 98.69.02.30

Dimensions:
M5 x 30mm

Stainless steel exhaust stud kit consisting of 4 x studs, 4 x dome head nuts, 4 x wavy washers and 4 x flat washers

On pre-1998 models we recommend combining with a pair of new exhaust polished aluminium flanges - EXA30032

 96508040 GU96508040 96 50 80 40
 9650 8040 9650.8040 96.50.80.40

Dimensions:
M8 x 40mm studs

M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins), also used for cylinder head bolt

See ACA12600 for aluminium alternative that can be undone by hand. Includes recess for O ring ENA90203

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

Dimensions:
M20 x 1.5

A2 stainless socket cap screw M10 x 55mm, many applications including lower yoke fork clamp bolts on Tonti models

Also known as Guzzi ref. 98620555

98072555-z 98072555 GU98072555 98 07 25 55
 9807 2555 9807.2555 98.07.25.55

Dimensions:
M10 x 55mm

M16 stainless steel full nut and thick washer for rear wheel spindle

Also referred to as Guzzi ref. 14634400 and 92602316

92602316-z 92602316 GU92602316 92 60 23 16
 9260 2316 9260.2316 92.60.23.16

Dimensions:
M16

Rear (longer) M12 socket cap stainless steel bolt for fixing footrest hanger to lower frame rail and upper frame

3 of these used on T3 lower frame rails

98623635-z 98623635 GU98623635 98 62 36 35
 9862 3635 9862.3635 98.62.36.35

Dimensions:
M12 x 35mm

M16 wavy stainless steel washer

Also known as a crinkle washer

95129260-z 95129260 GU95129260 95 12 92 60
 9512 9260 9512.9260 95.12.92.60

Stainless steel front engine mounting stud kit. Kit contains one long engine M12 x 1.25 threaded stud (with plain section in centre), two M12 half nuts, two M12 crinkle washers and four standard M12 washers - all in A2 stainless steel

The original bolts are prone to seizing in place so we recommend replacing with this quality stainless part. Also known as Guzzi ref. 03429500, 14429505
Differs from original part whcih is a bolt, this stud make is easier to fine tune the position of the stud between header pipes

 14429500 GU14429500 14 42 95 00
 1442 9500 1442.9500 14.42.95.00

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

Dimensions:
M10 single banjo fine thread