8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.

From late 2015 onwards 1200 models used SIA06428

See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump

More than 5 in stock

 30153000 GU30153000 30 15 30 00
 3015 3000 3015.3000 30.15.30.00

Air filter, cylindrical paper cartridge type

See SIA10422 for a reusable K & N air filter

More than 5 in stock

AP8104211

Air filter, flat paper cartridge type

See SIA10425 for a reusable performance air filter

More than 5 in stock

AP8104242

Carb gasket kit / rebuild kit for Dellorto VHB29, VHB30, VHB24 and VHB26 carbs

Carb overhaul kit, fuel filter FUA60888 and float bowl seal FUA90001 available separately to this seal kit. As this kit is intended for several different carbs you may have gaskets or O rings remaining after rebuilding. More information on rebuilding your VHB carb can be found here.

More than 5 in stock

 17939950 GU17939950 17 93 99 50
 1793 9950 1793.9950 17.93.99.50

Reusable oil filter, replaces original plastic filter with this sturdy metal filter and gauze

1 in stock

Single replacement caliper piston for Brembo P2 F09 or P9 caliper as fitted to Spada rear.

NB you will require a pair of these. Also used on Benelli Sei rear. Corresponding caliper seal kit is BRA54722

1 in stock

 20391310 GU20391310 20 39 13 10
 2039 1310 2039.1310 20.39.13.10

Also fits Benelli 900 Sei Rear (1983), Laverda 1000 RGS Fronts (1984)

UFI 25 531 00 cartridge oil filter for 1989 on small block engines

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check you old filter before ordering. Also known as Guzzi ref. 2A000633

More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Inlet rubber with HT lead guide. Fits between inlet manifold on cylinder head and throttle body or between throttle body and airbox

Also known as Guzzi ref. 03114370, 29114360. Use clip SSA45970.


Please note that if you are fitting this as a replacement to FUA30470 you may need to make some modification to the end of your airbox nozzle for a secure fit

More than 5 in stock

 30114370 GU30114370 30 11 43 70
 3011 4370 3011.4370 30.11.43.70

Clutch cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

4 in stock

14093051-z 14093051 GU14093051 14 09 30 51
 1409 3051 1409.3051 14.09.30.51

Complete Speedo (odometer) cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

More than 5 in stock

12760400-z 12760400 GU12760400 12 76 04 00
 1276 0400 1276.0400 12.76.04.00