5 pin 12 volt relay suitable for starter, lights, indicator, flasher and horn applications

Supercedes Guzzi ref. 12732500. Equivalent to 28732500 but with mounting bracket

 More than 5 in stock

19732500-z 19732500 GU19732500 19 73 25 00
 1973 2500 1973.2500 19.73.25.00

Pair of tubular chrome rocker cover protector bars for two valve engines with carbs of twin throttle bodies. These will protect barrels and rocker covers in the unfortunate event of your bike being dropped

These head protectors bolt to the head at three points using existing rocker cover bolts

 1 in stock

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 1 in stock

Manual right hand petrol tap with nut and filter. On, Off and Reserve settings.

Point on lever faces back in off position. Can be used to replace electronic fuel solenoid valve 37105305

 More than 5 in stock

17105460-z 17105460 GU17105460 17 10 54 60
 1710 5460 1710.5460 17.10.54.60

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Pair of timing springs for mechanical advance/retard mechanism

1 pair of distributor springs required per engine. Also known as Guzzi ref. 28753960, 28753960, 14715431. These are a finer grade wire than the springs used on the low compression models

 4 in stock

 28753950 GU28753950 28 75 39 50
 2875 3950 2875.3950 28.75.39.50

Breather valve or non return valve (ball type) for crankcase breather

Now comes as a kit of separate parts which need assembling.

 2 in stock

28150560-z 28150560 GU28150560 28 15 05 60
 2815 0560 2815.0560 28.15.05.60

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Front crank oil seal for models with Bosch or Ducati charging systems

Also known as Guzz ref. 90402839

 More than 5 in stock

90402840-Z

Lower Throttle cable

This runs from the splitter to the carb. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 2 in stock

 31117715 GU31117715 31 11 77 15
 3111 7715 3111.7715 31.11.77.15