Shop headings: New Spares | Used Spares | Accessories | Brands
Long alloy bellmouth intake / trumpet with domed mesh for Dellorto PHM 40 carb, screws to rear of carb replacing air filter
This part is available by special order, request a quote
£48.00
INC VAT
£40.00 EX VAT
Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression
Components for one cylinder. This kit can be fitted to a 850 crankcase if the crankcase aperture is enlarged. See similar kit ENA20050 for alternative
Sorry, this part is no longer available.
18060102-z 18060102 GU18060102 18 06 01 02
1806 0102 1806.0102 18.06.01.02
Sorry this item is out of production
Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression. This kit with Italian made piston and rings is an an alternative to Gilardoni kits which can often be in short supply.
Components for one cylinder. See ENA18102 for similar kit made by Gilardoni
2 in stock
18060102-z 18060102 GU18060102 18 06 01 02
1806 0102 1806.0102 18.06.01.02
£311.00
INC VAT
£259.17 EX VAT
Hepco pillion grab rail. Designed to unobtrusively provide security to pillions as well as offering a bungee tie down point.
If fitting pannier frames you will need to fit either this grab rail or LUA02067
This part is available by special order, request a quote
£92.00
INC VAT
£76.67 EX VAT
Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.
A great way to tidy up the pillion footrests on your project bike
Availability varies on this part, check availability
01163620 GU01163620 01 16 36 20
0116 3620 0116.3620 01.16.36.20
£39.90
INC VAT
£33.25 EX VAT
Passenger saddle featuring 3D net inserts for optimal ergonomics and long travel comfort.
This part is available by special order, request a quote
2S002031
£149.00
INC VAT
£124.17 EX VAT
HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10433 and V-Twin Boost - ACA85001 or ACA85002.
Customer Kev fitted this combo and called us the next day to say that his V85TT was transformed; the fluffy throttle response between 2k and 3k was gone and the engine pulled better. Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
1 in stock
£140.00
INC VAT
£116.67 EX VAT
HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
1 in stock
£160.00
INC VAT
£133.33 EX VAT
HIgh performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
This part is available by special order, request a quote
£140.00
INC VAT
£116.67 EX VAT
Pair of performance Dyna 12 volt 5 ohm single lead ignition coils with angled HT lead socket. These are a cooler running coil that offer improved starting and performance
Dyna Performance Replacment Coils are high tech, top quality coils, designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dynatek coils are available in a wide variety of resistances and output configurations to allow easy replacement of stock coils. Dynatek coils work with factory electronic ignitions, points, and aftermarket ignitions.
These are a different size and shape from the original coils so you will need to fabricate a suitable coil mount.
Individual coils available by special order, call us for details. See ELA00001 for crimp on HT lead connector
This part is due back in stock soon, call 01484 841395 to reserve yours
1471650
£190.00
INC VAT
£158.33 EX VAT