Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHBH 30 carb, replacing air filter. Clamp on type

Supplied with fixing clip, carb shown is for illustration purposes

 This part is available by special order, request a quote

Set of highly polished aluminium round barrel rocker covers (Guzzi ref. 17023550 or 17023560). Ideal for finishing off your restoration project

This rocker cover set also known as Guzzi ref. 14023550, these can be fited to square barrel models if fitted with adapter kit ACA30310

 This part is available by special order, request a quote

 17023560 GU17023560 17 02 35 60
 1702 3560 1702.3560 17.02.35.60

Long alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter

 2 in stock

Long alloy bellmouth intake / trumpet with domed mesh for Dellorto PHM 40 carb, screws to rear of carb replacing air filter

 This part is available by special order, request a quote

Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression

Components for one cylinder. This kit can be fitted to a 850 crankcase if the crankcase aperture is enlarged. See similar kit ENA20050 for alternative

 Sorry, this part is no longer available.

18060102-z 18060102 GU18060102 18 06 01 02
 1806 0102 1806.0102 18.06.01.02

Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression. This kit with Italian made piston and rings is an an alternative to Gilardoni kits which can often be in short supply.

Components for one cylinder. See ENA18102 for similar kit made by Gilardoni

 2 in stock

18060102-z 18060102 GU18060102 18 06 01 02
 1806 0102 1806.0102 18.06.01.02

Hepco pillion grab rail. Designed to unobtrusively provide security to pillions as well as offering a bungee tie down point.

If fitting pannier frames you will need to fit either this grab rail or LUA02067

 This part is available by special order, request a quote

Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.

A great way to tidy up the pillion footrests on your project bike

 Availability varies on this part, check availability

 01163620 GU01163620 01 16 36 20
 0116 3620 0116.3620 01.16.36.20

Passenger saddle featuring 3D net inserts for optimal ergonomics and long travel comfort.

 This part is available by special order, request a quote

2S002031

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10433 and V-Twin Boost - ACA85001 or ACA85002.

Customer Kev fitted this combo and called us the next day to say that his V85TT was transformed; the fluffy throttle response between 2k and 3k was gone and the engine pulled better. Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock