Complete double conrod for rear suspension on CARC models, connects rear shock to wishbone linkage. Includes all bearings, oil seals and bushes fitted to the conrod

Also known as Guzzi ref. GU055603304. Consists of Guzzi refs. AP8135924, AP8110066, AP8110068, GU05562030, AP8135608.

See TRA05430 for wishbone linkage

 1 in stock

 05560330 GU05560330 05 56 03 30
 0556 0330 0556.0330 05.56.03.30

Starter ring gear

See ENA98420 for bolts

 This part is available by special order, request a quote

 17067900 GU17067900 17 06 79 00
 1706 7900 1706.7900 17.06.79.00

Brembo PS 16 rear master cylinder for models with a remote reservoir, suitable as a replacement for the standard PS15 master cylinder which has now been discontinued by Brembo. Supplied with operating lever. Mounting holes at 50mm centres

Brembo ref. 10.2934.02 See BRA19500 for the elbow that the fluid supply pipe fits onto. Also see BRC19001 for a reconditioned PS15 MC

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19667000 GU19667000 19 66 70 00
 1966 7000 1966.7000 19.66.70.00

Reconditioned starter motor and solenoid for 2006 on models in black and silver finish. These units are high quality OE parts made by Bosch or Mitsubishi. Professionally reconditioned and sold with a 12 month guarantee

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address (see bottom of page). Not interchangeable with Valeo and Bosch starters from earlier models.

NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. Also known as Guzzi ref. 97729R

 05730730 GU05730730 05 73 07 30
 0573 0730 0573.0730 05.73.07.30

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

12 volt coil used on late Guzzis

Sometimes referred to as the 'square coil', two required per bike. See ELA00001 for crimp on HT lead connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30716500 GU30716500 30 71 65 00
 3071 6500 3071.6500 30.71.65.00

Polished rocker cover set for square barrel models consisting of 2 x rocker covers

Plain covers without any sensor mount holes

 This part is available by special order, request a quote

 03999540 GU03999540 03 99 95 40
 0399 9540 0399.9540 03.99.95.40

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 This part is due back in stock soon, call 01484 841395 to reserve yours

Brembo PS 13 handlebar mounted front master cylinder. The PS13 has a small rectangular fluid reservoir

Replaces Guzzi refs 28660178 and 30660180. Supplied complete with black or polished lever. Uses switch ELA30860

 This part is due back in stock soon, call 01484 841395 to reserve yours

 28660278 GU28660278 28 66 02 78
 2866 0278 2866.0278 28.66.02.78

Quality replacement fuel pump from Bosch

For models with the fuel pump mounted external to the fuel tank. No longer available new from Guzzi. Also known as Guzzi ref. 29107261 and 29107260

 Availability varies on this part, check availability

 01107231 GU01107231 01 10 72 31
 0110 7231 0110.7231 01.10.72.31