Kit containing 8 long titanium shouldered retaining screws for your rocker covers. Upgrades the poor quality OE screws with shiny Ti parts

Rocker cover bolt kit for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 More than 5 in stock

 887483 MG887483

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 2 in stock

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins), also used for cylinder head bolt

See ACA12600 for aluminium alternative that can be undone by hand. Includes recess for O ring ENA90203

 More than 5 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

M16 stainless steel full nut and thick washer for rear wheel spindle

Also referred to as Guzzi ref. 14634400 and 92602316

 More than 5 in stock

92602316-z 92602316 GU92602316 92 60 23 16
 9260 2316 9260.2316 92.60.23.16

Stainless steel drain plug for drive box and gearbox, includes recess for crush washer to locate in. Also used as level plug on big twins and front sump drain on small twins.

Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt

 More than 5 in stock

95980214-z 95980214 GU95980214 95 98 02 14
 9598 0214 9598.0214 95.98.02.14

M16 stainless steel half nut and washers for front wheel spindle. Includes flat and wavy washer

NB this is a half nut. Can also be used as alternator retaining nut 92603516

 More than 5 in stock

92602516-z 92602516 GU92602516 92 60 25 16
 9260 2516 9260.2516 92.60.25.16

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 5 in stock

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,