These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder unless the master cylinder is modified. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

See EXA14998 for matching large bore Lafranconi Competition silencers, combine these two parts for a complete large bore performance system

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes

We can also supply a headlamp ( LIA37593 or LIA37595 ), headlamp brackets, indicators and stems and most other parts you might need to turn your bike into Le Mans 1 lookalike, call or email for details

This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks

Part of the exciting range of MAS aluminium parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks. Does not fit V7 III

Part of the exciting range of MAS aluminium parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks.

Ideal for riders who wish to ride their cafe racer / sports bike in comfort, these bars have a useful 70mm rise, and can be arranged high and straight like standard handlebars, or low and mean like race clip ons, with plenty of adjustability inbetween.