Shop headings: New Spares | Used Spares | Accessories | Brands
46.5mm inlet valve
This part is available by special order, request a quote
37036005 GU37036005 37 03 60 05
3703 6005 3703.6005 37.03.60.05
£48.30
INC VAT
£40.25 EX VAT
39.5mm exhaust valve
This part is available by special order, request a quote
37036105 GU37036105 37 03 61 05
3703 6105 3703.6105 37.03.61.05
£48.30
INC VAT
£40.25 EX VAT
Circlip for gudgeon pin
Gudgeon pin clip also known as Guzzi ref. 90351039
This part is due back in stock soon, call 01484 841395 to reserve yours
90351038 GU90351038 90 35 10 38
9035 1038 9035.1038 90.35.10.38
£13.40
INC VAT
£11.17 EX VAT
Needle roller bearing for oil pump
This part is available by special order, request a quote
92252210 GU92252210 92 25 22 10
9225 2210 9225.2210 92.25.22.10
£29.20
INC VAT
£24.33 EX VAT
Special nut for retaining crankshaft timing sprocket
This part is available by special order, request a quote
92602525 GU92602525 92 60 25 25
9260 2525 9260.2525 92.60.25.25
£25.00
INC VAT
£20.83 EX VAT
Lock washer for sump oil gauze on big twins
This part is due back in stock soon, call 01484 841395 to reserve yours
95187006 GU95187006 95 18 70 06
9518 7006 9518.7006 95.18.70.06
£3.40
INC VAT
£2.83 EX VAT
Clutch adjustment locknut for gearbox rear, locks adjustment of freeplay on clutch arm. Also used as tappet adjuster nut on early 750 and Nuovo Falcone models
Also known as Guzzi ref. 92606508
This part is due back in stock soon, call 01484 841395 to reserve yours
92602508 GU92602508 92 60 25 08
9260 2508 9260.2508 92.60.25.08
£0.90
INC VAT
£0.75 EX VAT
Tool for crankshaft timing sprocket nut, this is a superior design tool intended for repeated use. Use for clutch centre nut on V11 Sport. Will not reach timing sprocket nut on models with Ducati charging system.
Also fits swingarm spindle nut on Stelvio.
Half inch socket drive
This part is due back in stock soon, call 01484 841395 to reserve yours
18927651 GU18927651 18 92 76 51
1892 7651 1892.7651 18.92.76.51
£41.00
INC VAT
£34.17 EX VAT
Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings
For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models
This part is available by special order, request a quote
£48.00
INC VAT
£40.00 EX VAT
Outer valve spring on big valve two valve Tonti frame models or driveshaft spring for spine frame models
This part is due back in stock soon, call 01484 841395 to reserve yours
28037460-z 28037460 GU28037460 28 03 74 60
2803 7460 2803.7460 28.03.74.60
£8.30
INC VAT
£6.92 EX VAT