S&B air filter. Offset mounting, chromed back, includes clip. Fits Dellorto PHF36 and PHF30 carbs.

This K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable. Best run dry for road. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter. Either ENA14700 or ENA14157 can be used as a breather box to replace the unit in the airbox on round barrel models

 More than 5 in stock

Fibreglass triangular V7 Sport style side panel. Supplied unpainted, undrilled and without fixings. Ideal for the home special builder

Designed for early Tonti frames but may fit other models after appropriate modifications have been made. Two panels required per bike

 More than 5 in stock

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes

 2 in stock

Chrome plug or bolt cover for M10 socket head bolts, tidies up screw heads

 2 in stock

 23943510 GU23943510 23 94 35 10
 2394 3510 2394.3510 23.94.35.10

Special Inlet rubber with HT lead guide for late Dellorto PHM carbs with a inlet stub OD of 46mm

Use clip SSA45970
This part will only fit late PHM40 carbs with 46mm inlet stubs, we recommend measuring your carbs before ordering

 2 in stock

Complete shallow bowl 190mm chrome headlight unit. Includes a pilot / parking light. A shallow bowl makes it especially suitable for mounting on Moto Guzzis underneath the instruments

Homologated for road use.

Supplied complete with H4 bulb, pilot light and four short wires (without connectors). This headlight will fit fairing cowling FAA99575 for Le Mans 1 conversions if trim strip is not fitted to inside edge of fairing. NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems

 2 in stock

Rubber sleeved folding riders footpeg, suitable for Tarozzi rearsets and as an upgrade for standard footrests

Folding footrest

 1 in stock

Chrome plug or bolt cover for M8 socket head bolts, tidies up screw heads

 1 in stock

 23943410 GU23943410 23 94 34 10
 2394 3410 2394.3410 23.94.34.10

Pair of Tommaselli chromed headlight brackets with anti vibration rubber collars and silver finish aluminium brackets. To fit 35mm and 36mm diameter forks.

 1 in stock

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock