The BoosterPlug is an effective and cost efficient way to cure the fuelling problems on twin throttle body V7 mark 1 models.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Improved fuel economy

The BoosterPlug is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Booster plug removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Lifetime warranty

 This part is due back in stock soon, call 01484 841395 to reserve yours

Rocker cover screw kit containing 12 replacement stainless steel socket cap bolts for two valve small twin rocker covers. Only one kit required per engine. Only for twin throttle body V7 models

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted. This kit contains the correct screws for the Breva 750 and 2004 on V7 models but does not include the two flanged M5 screws SSA81523 that fasten the rocker cover covers to the rocker cover (on models other than the V7 Racer)

 More than 5 in stock

Kit containing 8 long titanium shouldered retaining screws for your rocker covers. Upgrades the poor quality OE screws with shiny Ti parts

Rocker cover bolt kit for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 More than 5 in stock

 887483 MG887483

Screw kit containing 28 replacement stainless steel socket cap bolts for timing cover, inlet manifolds and sump pan. Only one kit required per engine. See SSA87983 and SSA89291 for special rocker cover screw kits

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070).

Add a bit of sparkle to your V7!

 More than 5 in stock

Kit containing 6 titanium shouldered retaining screw for rocker cover. Upgrade your corrosion prone zinc OE parts with a polished upgrade. Note that one bolt on each cover is hidden under a plastic cover, if you would prefer to only buy four bolts then see SSA84291

Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer

 More than 5 in stock

 842291 MG842291

Titanium shouldered retaining screw for rocker cover. 4 required for each cylinder head

Rocker cover bolt for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 More than 5 in stock

 887483 MG887483

Titanium shouldered retaining screw for rocker cover. 4 required for each big twin cylinder head, 3 per head on small twins. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer on CARC models and ENA06716 for sealing washer on other models

 More than 5 in stock

 842291 MG842291

Red sticker celebrating 100 years of Moto Guzzi. Featuring the names of the 3 men who were behind the birth of Moto Guzzi this is a great way to commemorate the centenary of the marque.

Red sticker with white border. Ideal for covering up marks on bodywork!

 More than 5 in stock

Replacement blue LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002

These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED

 More than 5 in stock