Smarten up the rear of your V7 with this fenda eliminator kit with includes an LED tail light.
This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks
2 in stock
£185.20
INC VAT
£154.33 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
Dellorto needle valve kit comprising of valve and felt washer
200 needle valve for VHB24, VHB26 and PHBH carbs
5 in stock
19934600 GU19934600 19 93 46 00
1993 4600 1993.4600 19.93.46.00
£20.30
INC VAT
£16.92 EX VAT
Manual square bodied fuel tap with nut, washer and filter
Off, on and reserve positions. Approved for use with fuel containing ethanol
2 in stock
14105400-z 14105400 GU14105400 14 10 54 00
1410 5400 1410.5400 14.10.54.00
£40.00
INC VAT
£33.33 EX VAT
44mm inlet valve
Also known as Guzzi ref. 03036000
3 in stock
14036050 GU14036050 14 03 60 50
1403 6050 1403.6050 14.03.60.50
£35.00
INC VAT
£29.17 EX VAT
37mm exhaust valve
Also known as Guzzi ref. 03036100
3 in stock
14036150 GU14036150 14 03 61 50
1403 6150 1403.6150 14.03.61.50
£30.00
INC VAT
£25.00 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
Complete cast side stand with springs, pivot and mounting bracket finished in black. This stand is the original flip up / self retracting type
Bolts to engine mounting bolt at front of lower framerail, check that you have a long enough front engine mounting bolt for this sidestand to fit on to. This can be fitted to other Tonti frame models (e.g. Le Mans 1000). See FRA28162 for bracket that enables this stand to be mounted near the rider's footrest using the gearbox mounting bolt.
1 in stock
17432060-z 17432060 GU17432060 17 43 20 60
1743 2060 1743.2060 17.43.20.60
£99.00
INC VAT
£82.50 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
1 in stock
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Throttle cable for models with plastic twistgrip and switchgear
Only suitable for post 1979 models. We advise you to measure your existing cable before ordering in case you have a non standard set up.
4 in stock
18117560 GU18117560 18 11 75 60
1811 7560 1811.7560 18.11.75.60
£10.00
INC VAT
£8.33 EX VAT