Air filter, cylindrical paper cartridge type
See SIA10422 for a reusable K & N air filter
More than 5 in stock
AP8104211
£11.70
INC VAT
£9.75 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
Pinion roller bearing for drive box
1 in stock
92249227-z 92249227 GU92249227 92 24 92 27
9224 9227 9224.9227 92.24.92.27
£26.50
INC VAT
£22.08 EX VAT
Silencer clamp gasket / shim or muffler gasket used to seal crossover to silencer
This exhaust bush is not required if a Mistral or Agostini silencer is fitted
1 in stock
05128230 GU05128230 05 12 82 30
0512 8230 0512.8230 05.12.82.30
£25.00
INC VAT
£20.83 EX VAT
Head Gasket
5 in stock
30022060 GU30022060 30 02 20 60
3002 2060 3002.2060 30.02.20.60
£14.40
INC VAT
£12.00 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT
Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems
These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt
More than 5 in stock
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT
Thin walled spark plug spanner for 10mm plugs including the small long life PMR8B spark plug fitted to CARC models
More than 5 in stock
05901930-z 05901930 GU05901930 05 90 19 30
0590 1930 0590.1930 05.90.19.30
£17.00
INC VAT
£14.17 EX VAT