Steel fixed front right brake pipe with threaded connectors at each end

Rigid brake pipe

 1 in stock

 17658050 GU17658050 17 65 80 50
 1765 8050 1765.8050 17.65.80.50

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems

These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt

 More than 5 in stock

Also fits Benelli 250 TS

Pair of Moto Guzzi engine crash bars finished in black. The heads and rocker covers are vulnerable on these bikes and can be badly damaged by even a minor accident, replacement cost can be more than £1000 so protect your bike with these engine bars

See this link for installation instructions.

 1 in stock

Clutch pushrod seal

 More than 5 in stock

 90400616 GU90400616 90 40 06 16
 9040 0616 9040.0616 90.40.06.16

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

Rear crank oil seal

Fits Nevada 750 from engine LT017877 and Nevada 350 from PC053625. NB Original specification 12mm seal no longer in production, our seal is 10mm thick. Superceded by Guzzi ref. 886365

 3 in stock

04000500-z 04000500 GU04000500 04 00 05 00
 0400 0500 0400.0500 04.00.05.00

Pair of universal Tommaselli black handlebars, low rise

Include threaded bar end inserts for bar end weights

 1 in stock

 32600310 GU32600310 32 60 03 10
 3260 0310 3260.0310 32.60.03.10

Air filter, flat paper cartridge type for models with single throttle body

See SIA10434 for a reusable performance air filter

 4 in stock

AP8104924