Black rubber battery mat
This is the larger battery tray fitted to Tonti framed models
3 in stock
14707000 GU14707000 14 70 70 00
1470 7000 1470.7000 14.70.70.00
£12.20
INC VAT
£10.17 EX VAT
Oil pressure sender
Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.
See ENA12640 for replacement crush washer if required
5 in stock
19768720-z 19768720 GU19768720 19 76 87 20
1976 8720 1976.8720 19.76.87.20
£15.50
INC VAT
£12.92 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
Rear crankcase oil seal or rear main oil seal.
Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch
More than 5 in stock
90405367-z 90405367 GU90405367 90 40 53 67
9040 5367 9040.5367 90.40.53.67
£14.00
INC VAT
£11.67 EX VAT
Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models
Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )
More than 5 in stock
90413850 GU90413850 90 41 38 50
9041 3850 9041.3850 90.41.38.50
£9.80
INC VAT
£8.17 EX VAT
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£11.00
INC VAT
£9.17 EX VAT
Gearbox output seal on later small twins (V50 3 and V35 II on) and all V65 and 750cc models. Also gearbox input seal on V50 3, V35 II, V35 III, Imola, V35 Florida, V35C, V50C, Monza
Replaces Guzzi ref. AP9150435 and 886629
More than 5 in stock
90402841 GU90402841 90 40 28 41
9040 2841 9040.2841 90.40.28.41
£9.00
INC VAT
£7.50 EX VAT
Clutch cable
We advise you to measure your existing cable before ordering in case you have a non standard set up
1 in stock
2B001202
£23.00
INC VAT
£19.17 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT