Dimensions:
M10 conventional thread, 105mm diameter head, 180mm approx reach
Chrome finish mirror, especially suited to T3, V50 and similar models. Conventional M10 thread, head is socket mounted for left or right hand fitment. Head is chromed plastic, stem is chromed steel.
M10 thread
3 in stock
£20.50
INC VAT
£17.08 EX VAT 
Dimensions:
115mm x 155mm x 28mm
Air filter, flat paper cartridge type
See SIA10425 for a reusable performance air filter
More than 5 in stock
AP8104242
£12.00
INC VAT
£10.00 EX VAT
Standard air filter
2 in stock
2B009776
£72.00
INC VAT
£60.00 EX VAT
Dimensions:
Outer 1130 mm free length 105 mm
Clutch cable
We advise you to measure your existing cable before ordering in case you have a non standard set up
1 in stock
2B001202
£23.00
INC VAT
£19.17 EX VAT
Dimensions:
100cm
One metre of copper core HT lead, this is superior to the more commonly available carbon core lead
Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector
More than 5 in stock
£7.00
INC VAT
£5.83 EX VAT
Dimensions:
40mm OD
Gearbox output seal on later small twins (V50 3 and V35 II on) and all V65 and 750cc models. Also gearbox input seal on V50 3, V35 II, V35 III, Imola, V35 Florida, V35C, V50C, Monza
Replaces Guzzi ref. AP9150435 and 886629
More than 5 in stock
90402841 GU90402841 90 40 28 41
9040 2841 9040.2841 90.40.28.41
£9.00
INC VAT
£7.50 EX VAT
Dellorto 260 needle jet or atomiser for VHB24 and VHB26 carbs
2 in stock
19935501 GU19935501 19 93 55 01
1993 5501 1993.5501 19.93.55.01
£15.00
INC VAT
£12.50 EX VAT
Dimensions:
84mm x 77mm diameter overall, for 19mm OD spigot. HF552 is probably Hi Flo alternative
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
60/55W H4 P43T headlamp / headlight bulb
This is the more modern H4 bulb with three tabs . Also known as Guzzi ref. 292723
2 in stock
93450232 GU93450232 93 45 02 32
9345 0232 9345.0232 93.45.02.32
£6.10
INC VAT
£5.08 EX VAT
Dimensions:
35mm x 47mm x 7/9mm
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£11.00
INC VAT
£9.17 EX VAT
Secure online shopping 
