Final drive inner output seal
For Breva 750 from frame no. LL111908
4 in stock
90407591-z 90407591 GU90407591 90 40 75 91
9040 7591 9040.7591 90.40.75.91
£15.80
INC VAT
£13.17 EX VAT
Drive box input seal
Pinion oil seal
More than 5 in stock
90403251-z 90403251 GU90403251 90 40 32 51
9040 3251 9040.3251 90.40.32.51
£16.60
INC VAT
£13.83 EX VAT
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£11.00
INC VAT
£9.17 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
Pinion roller bearing for drive box
1 in stock
92249227-z 92249227 GU92249227 92 24 92 27
9224 9227 9224.9227 92.24.92.27
£26.50
INC VAT
£22.08 EX VAT
Updated bush with thicker rubber section for front of torque arm / cardan arm / reaction rod on CARC models
1 in stock
883045 MG883045
£28.00
INC VAT
£23.33 EX VAT
One piece collet for exhaust manifold, one required per cylinder
No longer in production
3 in stock
14121200 GU14121200 14 12 12 00
1412 1200 1412.1200 14.12.12.00
£15.00
INC VAT
£12.50 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT