Single metal fuel banjo for Dellorto carbs. Fuel filter FUA60888 sits inside this part and makes seal to carb
Also known as Guzzi ref. 10934600 and Ducati ref. 075527250
More than 5 in stock
13934600 GU13934600 13 93 46 00
1393 4600 1393.4600 13.93.46.00
Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 600 SL Pantah, Ducati 750/900 SS Koewe, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, S2, Ducati 900 MHR-I, Ducati 1000 MHR-2,S2
£7.80
INC VAT
£6.50 EX VAT
Input shaft oil seal for gearbox
More than 5 in stock
90403245 GU90403245 90 40 32 45
9040 3245 9040.3245 90.40.32.45
£9.00
INC VAT
£7.50 EX VAT
Polished stainless steel H pipe / collector / balance pipe for models without Lambda probe. Replaces heavy catalytic converter fitted to some models and improves access for oil changes
NB this crossover does not include exhaust clamps. Also available in a satin finish. Made to order in Italy by performance experts Mistral
1 in stock
03123900 GU03123900 03 12 39 00
0312 3900 0312.3900 03.12.39.00
£105.00
INC VAT
£87.50 EX VAT
Air filter, flat paper cartridge type for models with single throttle body
See SIA10434 for a reusable performance air filter
More than 5 in stock
AP8104924
£17.00
INC VAT
£14.17 EX VAT
UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633
More than 5 in stock
27153085 GU27153085 27 15 30 85
2715 3085 2715.3085 27.15.30.85
£9.50
INC VAT
£7.92 EX VAT
Air filter, flat paper cartridge type for models with single throttle body
See SIA10434 for a reusable performance air filter
More than 5 in stock
AP8104924
£17.00
INC VAT
£14.17 EX VAT
Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates
Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes
1 in stock
30906510 GU30906510 30 90 65 10
3090 6510 3090.6510 30.90.65.10
£110.00
INC VAT
£91.67 EX VAT
Heavy duty spring used for centrestand and sidestand applications
More than 5 in stock
12434001-z 12434001 GU12434001 12 43 40 01
1243 4001 1243.4001 12.43.40.01
£9.00
INC VAT
£7.50 EX VAT
Pair of organic EBC FA256 rear brake pads
Twin pin fitting. Pre 2012 V7 models use a different brake pad with only one pad pin hole. Also known as Guzzi ref 2R000248
4 in stock
AP8133798
£19.30
INC VAT
£16.08 EX VAT
Final drive inner seal
For Breva 750 up to frame no. LL111907
More than 5 in stock
90407590-z 90407590 GU90407590 90 40 75 90
9040 7590 9040.7590 90.40.75.90
£9.00
INC VAT
£7.50 EX VAT