Dimensions:
Springs are 23mm and 24mm respectively
Pair of timing springs for mechanical advance/retard mechanism
1 pair of distributor springs required per engine. Also known as Guzzi ref. 28753960, 28753960, 14715431. These are a finer grade wire than the springs used on the low compression models
4 in stock
28753950 GU28753950 28 75 39 50
2875 3950 2875.3950 28.75.39.50
£10.20
INC VAT
£8.50 EX VAT
Dimensions:
8mm ID x 16mm/18mm OD x 22mm
Breather valve or non return valve (ball type) for crankcase breather
Now comes as a kit of separate parts which need assembling.
2 in stock
28150560-z 28150560 GU28150560 28 15 05 60
2815 0560 2815.0560 28.15.05.60
£13.20
INC VAT
£11.00 EX VAT
Dimensions:
10mm threaded shank, 8mm across flats
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
Dimensions:
28mm x 38mm x 7mm
Front crank oil seal for models with Bosch or Ducati charging systems
Also known as Guzz ref. 90402839
More than 5 in stock
90402840-Z
£9.50
INC VAT
£7.92 EX VAT
Dimensions:
317mm outer length, 118mm free length, 2.7mm barrel nipple, 2.7mm barrel nipple
Lower Throttle cable
This runs from the splitter to the carb. We advise you to measure your existing cable before ordering in case you have a non standard set up.
2 in stock
31117715 GU31117715 31 11 77 15
3111 7715 3111.7715 31.11.77.15
£9.30
INC VAT
£7.75 EX VAT
Dimensions:
29mm x 24mm x 12mm excluding switch and spade connectors
Brakelight switch
Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw
3 in stock
03749845-z 03749845 GU03749845 03 74 98 45
0374 9845 0374.9845 03.74.98.45
£15.50
INC VAT
£12.92 EX VAT
Dimensions:
M12 x 1 thread, 32mm height from top of thread
Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator
See ENA12640 for replacement crush washer and ELA10005 for female spade connector
5 in stock
31768780 GU31768780 31 76 87 80
3176 8780 3176.8780 31.76.87.80
£11.00
INC VAT
£9.17 EX VAT
Dimensions:
47mm OD
Drive box input seal
Pinion oil seal
More than 5 in stock
90403251-z 90403251 GU90403251 90 40 32 51
9040 3251 9040.3251 90.40.32.51
£16.60
INC VAT
£13.83 EX VAT
Dimensions:
20mm x 6mm x 9mm excluding spade connectors
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.
3 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£13.50
INC VAT
£11.25 EX VAT
Dimensions:
M12 x 1 thread, 32mm height from top of thread
Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator
See ENA12640 for replacement crush washer and ELA10005 for female spade connector
5 in stock
31768780 GU31768780 31 76 87 80
3176 8780 3176.8780 31.76.87.80
£11.00
INC VAT
£9.17 EX VAT
Secure online shopping 
