Riders footpeg rubber in black, embossed with 'Moto Guzzi'
2 in stock
12443200-z 12443200 GU12443200 12 44 32 00
1244 3200 1244.3200 12.44.32.00
£7.50
INC VAT
£6.25 EX VAT
Riders footpeg rubber, black with chamfered underside
More than 5 in stock
39443200-z 39443200 GU39443200 39 44 32 00
3944 3200 3944.3200 39.44.32.00
£7.00
INC VAT
£5.83 EX VAT
Complete single disc clutch kit for 5 speed big twins containing flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. Suitable for all big twins with either distributor or crankshaft mounted ignition system, not suitable for Digiplex equipped models.
This clutch upgrade has the following advanges over the old two plate clutch:
1 in stock
£495.00
INC VAT
£412.50 EX VAT
Original type clutch friction plate for big twins
2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub. Also known as Guzzi ref. 12084400
4 in stock
28084460-z 28084460 GU28084460 28 08 44 60
2808 4460 2808.4460 28.08.44.60
£52.00
INC VAT
£43.33 EX VAT
Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders
Also known as Brembo ref. 110312720
5 in stock
19659500 GU19659500 19 65 95 00
1965 9500 1965.9500 19.65.95.00
£7.50
INC VAT
£6.25 EX VAT
Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.
Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear
1 in stock
01738030 GU01738030 01 73 80 30
0173 8030 0173.8030 01.73.80.30
£88.00
INC VAT
£73.33 EX VAT
Chrome twin pull Tommaselli 2c twist grip. Includes a pair of handlebar grips, for bikes with dual throttle cables from the bars
As originally fitted to pre 1979 T3's. Not suitable for carbs larger than 36mm (the twistgrip inner will require minor modification to operate PHM40s). This twistgrip can be used on almost any model with suitable custom cables. See ACA14450 for spare rubber. Holes for throttle cable elbow may be smaller than the original and need carefully enlarging with a drill or round file.
1 in stock
14603450 GU14603450 14 60 34 50
1460 3450 1460.3450 14.60.34.50
£90.00
INC VAT
£75.00 EX VAT
Carbon look low mudguard upgrade that hugs the front wheel to reduce spray from your front wheel. A popular modification for bikes that will mainly be used on road
For improved weather protection see ACA58195 for a compatible mudguard extension
1 in stock
£69.00
INC VAT
£57.50 EX VAT
Mesh silencer gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe
2 exhaust bushes required per bike
2 in stock
2B007137
£9.00
INC VAT
£7.50 EX VAT
Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates
Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes
1 in stock
30906510 GU30906510 30 90 65 10
3090 6510 3090.6510 30.90.65.10
£110.00
INC VAT
£91.67 EX VAT