Pair of sintered EBC FA095 HH brake pads for Brembo 5165 single pin four piston calipers
With the highest friction rating and a lifetime which is the envy of other Brake Pad Manufacturers, the Double-H pads are now available in a new quieter running, faster bedding formulation. NB if opting for sintered pads use them all round. We advise checking your front caliper(s) have one not two pad pins
2 in stock
30654602-z 30654602 GU30654602 30 65 46 02
3065 4602 3065.4602 30.65.46.02
£24.40
INC VAT
£20.33 EX VAT
Output oil seal for drive box
This oil seal fits output side of bevel box
More than 5 in stock
90407085-z 90407085 GU90407085 90 40 70 85
9040 7085 9040.7085 90.40.70.85
£14.00
INC VAT
£11.67 EX VAT
Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap
Stop light switch also known as Guzzi ref. 63657000
More than 5 in stock
79654116 GU79654116 79 65 41 16
7965 4116 7965.4116 79.65.41.16
Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2
£21.40
INC VAT
£17.83 EX VAT
New type clutch friction plate for models with deep splines with deep splined centre
2 plates required- thicker side of each friction plate should face transmission.
Also known as Guzzi ref. 30084410, 03084400, 29084450
V11 Tenni, Rosso Mandello and Scura have a single plate clutch which uses a different friction plate (unfortunately out of production)
These can be fitted to earlier 850 and 1000 models if the early shallow splined clutch centre is replaced with the later deep splined type. See our kit CLA20302 to update early 850/1000 models. Clutch plate alignment tool also available, see TOA30510
More than 5 in stock
05084430 GU05084430 05 08 44 30
0508 4430 0508.4430 05.08.44.30
£57.70
INC VAT
£48.08 EX VAT
Final drive inner output seal
For Breva 750 from frame no. LL111908
4 in stock
90407591-z 90407591 GU90407591 90 40 75 91
9040 7591 9040.7591 90.40.75.91
£15.80
INC VAT
£13.17 EX VAT
Manual square bodied fuel tap with nut, washer and filter. Fits left or right hand side of tank.
Off, on and reserve positions. Approved for use with fuel containing ethanol.
2 in stock
14105400-z 14105400 GU14105400 14 10 54 00
1410 5400 1410.5400 14.10.54.00
£40.00
INC VAT
£33.33 EX VAT
Air filter, flat paper cartridge type
See SIA10425 for a reusable performance air filter
More than 5 in stock
AP8104242
£12.00
INC VAT
£10.00 EX VAT
Pinion roller bearing for drive box
1 in stock
92249227-z 92249227 GU92249227 92 24 92 27
9224 9227 9224.9227 92.24.92.27
£26.50
INC VAT
£22.08 EX VAT
Regulator rectifier for Saprisa charging systems
Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part.
1 in stock
28703800-z 28703800 GU28703800 28 70 38 00
2870 3800 2870.3800 28.70.38.00
£85.00
INC VAT
£70.83 EX VAT
Dellorto E2 needle
Standard needle clip position is 2nd from top
2 in stock
19934900 GU19934900 19 93 49 00
1993 4900 1993.4900 19.93.49.00
£15.60
INC VAT
£13.00 EX VAT