Dellorto E2 needle
Standard needle clip position is 2nd from top
2 in stock
19934900 GU19934900 19 93 49 00
1993 4900 1993.4900 19.93.49.00
£15.60
INC VAT
£13.00 EX VAT
Pair of timing springs for mechanical advance/retard mechanism
1 pair of distributor springs required per engine. Also known as Guzzi ref. 28753960, 28753960, 14715431. These are a finer grade wire than the springs used on the low compression models
4 in stock
28753950 GU28753950 28 75 39 50
2875 3950 2875.3950 28.75.39.50
£10.20
INC VAT
£8.50 EX VAT
Breather valve or non return valve (ball type) for crankcase breather
Now comes as a kit of separate parts which need assembling.
2 in stock
28150560-z 28150560 GU28150560 28 15 05 60
2815 0560 2815.0560 28.15.05.60
£13.20
INC VAT
£11.00 EX VAT
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
1 in stock
£28.00
INC VAT
£23.33 EX VAT
Clutch cable without adjuster
1 in stock
23093070-z 23093070 GU23093070 23 09 30 70
2309 3070 2309.3070 23.09.30.70
£16.90
INC VAT
£14.08 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
2 in stock
£186.50
INC VAT
£155.42 EX VAT
Dimensions:
35mm internal diameter x 70mm tall collar, approx. 105mm reach from stanchion to headlight bolt
Pair of Tommaselli chromed headlight brackets with anti vibration rubber collars and silver finish aluminium brackets. To fit 35mm and 36mm diameter forks.
1 in stock
£57.00
INC VAT
£47.50 EX VAT
Regulator rectifier for Saprisa charging systems
Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part.
1 in stock
28703800-z 28703800 GU28703800 28 70 38 00
2870 3800 2870.3800 28.70.38.00
£85.00
INC VAT
£70.83 EX VAT
Pair of Wirth progressive fork springs
These progressive fork springs improve ride quality and handling by responding progressively to the road. The more the spring is compressed the harder it becomes preventing the forks from bottoming out. See OIA01001 for fork oil
1 in stock
18526960-z 18526960 GU18526960 18 52 69 60
1852 6960 1852.6960 18.52.69.60
Also fits Benelli Sei 900
£130.00
INC VAT
£108.33 EX VAT
Black PS 12 master cylinder (original round type). Supplied without lever. Currently unavailble- see BRA28278 for an alternative master cylinder.
Also known as Guzzi ref. 28660178, uses seal kit BRA14701 and lever BRA14605 (or BRA17606). Replaces Guzzi refs. 17660250, 17660252, 14660200, 082054335. Can be used to upgrade cable operated front master cylinder on V35 I, V50 I and V50 II models. also suitable for 750S
1 in stock
17660253 GU17660253 17 66 02 53
1766 0253 1766.0253 17.66.02.53
Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei
£139.00
INC VAT
£115.83 EX VAT