Dellorto E2 needle

Standard needle clip position is 2nd from top

 2 in stock

 19934900 GU19934900 19 93 49 00
 1993 4900 1993.4900 19.93.49.00

Pair of timing springs for mechanical advance/retard mechanism

1 pair of distributor springs required per engine. Also known as Guzzi ref. 28753960, 28753960, 14715431. These are a finer grade wire than the springs used on the low compression models

 4 in stock

 28753950 GU28753950 28 75 39 50
 2875 3950 2875.3950 28.75.39.50

Breather valve or non return valve (ball type) for crankcase breather

Now comes as a kit of separate parts which need assembling.

 2 in stock

28150560-z 28150560 GU28150560 28 15 05 60
 2815 0560 2815.0560 28.15.05.60

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 1 in stock

Clutch cable without adjuster

 1 in stock

23093070-z 23093070 GU23093070 23 09 30 70
 2309 3070 2309.3070 23.09.30.70

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 2 in stock

Pair of Tommaselli chromed headlight brackets with anti vibration rubber collars and silver finish aluminium brackets. To fit 35mm and 36mm diameter forks.

 1 in stock

Regulator rectifier for Saprisa charging systems

Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part.

 1 in stock

28703800-z 28703800 GU28703800 28 70 38 00
 2870 3800 2870.3800 28.70.38.00

Pair of Wirth progressive fork springs

These progressive fork springs improve ride quality and handling by responding progressively to the road. The more the spring is compressed the harder it becomes preventing the forks from bottoming out. See OIA01001 for fork oil

 1 in stock

18526960-z 18526960 GU18526960 18 52 69 60
 1852 6960 1852.6960 18.52.69.60

Also fits Benelli Sei 900

Black PS 12 master cylinder (original round type). Supplied without lever. Currently unavailble- see BRA28278 for an alternative master cylinder.

Also known as Guzzi ref. 28660178, uses seal kit BRA14701 and lever BRA14605 (or BRA17606). Replaces Guzzi refs. 17660250, 17660252, 14660200, 082054335. Can be used to upgrade cable operated front master cylinder on V35 I, V50 I and V50 II models. also suitable for 750S

 1 in stock

 17660253 GU17660253 17 66 02 53
 1766 0253 1766.0253 17.66.02.53

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei