Page 3 of 27
Choke Lever Assembly Dellorto PHF & VHB30 FUA14800 Fits Le Mans 1, Le Mans 2, Le Mans 3, Cali 3, Strada 1000, 850 GT, G5, Cali 2, 1000 SP, T3, T4, 850T, V7 Sport, 750S, S3, Nuovo Falcone Dimensions: 8mm OD x 20mm brass plunger Carb mounted flip choke with plunger, lever, O ring, casting and spring. Insufficient clearance on high top carbs to operate the choke and the throttle cable
Fits all PHF30 - PHF36 and VHB30 Dellorto flat top carbs, contains rubber seat insert. Allows you to eliminate the choke cables and any handlebar choke controls for a cleaner look, especially suitable for special builds 4 in stock 14937800 GU14937800 14 93 78 00 1493 7800 1493.7800 14.93.78.00 £21.80 INC VAT £18.17 EX VAT
Gearbox Input Seal TRA90059 Fits MGS-01, V11 Sport Dimensions: 40mm x 56mm x 7mm Gearbox Input Seal 1 in stock 90404059 GU90404059 90 40 40 59 9040 4059 9040.4059 90.40.40.59 £16.60 INC VAT £13.83 EX VAT
Float FUA19380 Fits V65 ALL, V35 ALL, V50 ALL, Nevada 750 (1991-2003), Nevada 350 Dellorto 9.5g float with tang for needle valve. May come in black or white Also known as Guzzi ref. 61934300, 27934315
2 in stock 19934380 GU19934380 19 93 43 80 1993 4380 1993.4380 19.93.43.80 £19.80 INC VAT £16.50 EX VAT
Fork Dust Seal SUA28525 Fits Le Mans 1000 (1986-1988) Dimensions: 40mm internal diameter at narrow end, 51mm internal diameter at wide end, 35mm height Dust cover for fork stanchion, seals against stanchion and protects fork seal 2 in stock 28524560-z 28524560 GU28524560 28 52 45 60 2852 4560 2852.4560 28.52.45.60 £8.60 INC VAT £7.17 EX VAT
Fork Dust Seal SUA28524 Fits T5, V65 Florida, SP II, V75 (4 Valve) Dimensions: 52mm internal diameter at large end, 38mm internal diameter at narrow end Dust cover for fork stanchion, seals against stanchion to protect fork seal. 4 in stock 28524500-z 28524500 GU28524500 28 52 45 00 2852 4500 2852.4500 28.52.45.00 £8.80 INC VAT £7.33 EX VAT
Tail Light Lens LIA65700 Fits 1000 SP, T4, T3 (1980-1983), Le Mans 1 (series 2), G5 (series 2), Convert (series 2), Le Mans 2, Le Mans 3, V35 I, V35 II, V50 I, V50 I, V50 II, V50 3, V65, 750T Red lens for oblong rear light, includes clear section to illuminate number plate Can be used to replace tail light lens on Lario and Le Mans 1000, note that this one does not have side 'wings' but is functional on these models 1 in stock 65741700 GU65741700 65 74 17 00 6574 1700 6574.1700 65.74.17.00 £14.50 INC VAT £12.08 EX VAT
Footrest Rubber Front FRA90201 Fits Le Mans 1000, 1000S, Mille GT, Spada 3, T5, SP II, 750 Targa, Strada 1000, Lario, V75, Strada 750, V50 Carabineri (1992 - 2001), V35 3, Imola 2 Dimensions: 95mm x 43mm x 40m overall. Peg hole diameter 19mm Riders footpeg rubber, black with chamfered underside 4 in stock 28443201-z 28443201 GU28443201 28 44 32 01 2844 3201 2844.3201 28.44.32.01 £7.60 INC VAT £6.33 EX VAT
Footrest Rubber Riders FRA12300 Fits V7 700, V7 Special (1969-1971), 850 GT, Nuovo Falcone Dimensions: 23mm ID x 44mm OD x 114mm Riders footpeg rubber in black, embossed with 'Moto Guzzi' 2 in stock 12443200-z 12443200 GU12443200 12 44 32 00 1244 3200 1244.3200 12.44.32.00 £7.50 INC VAT £6.25 EX VAT
Footrest Rubber Front FRA39200 Fits V35 I, V35 II, Imola, V35C, V50 I, V50 II, V50C, V50 3, Monza, V65 (1981-1987), V65C, 350 GTS, 400 GTS Dimensions: 110mm 50mm x 34mm overall Riders footpeg rubber, black with chamfered underside More than 5 in stock 39443200-z 39443200 GU39443200 39 44 32 00 3944 3200 3944.3200 39.44.32.00 £7.00 INC VAT £5.83 EX VAT
RAM Clutch Kit Upgrade CLA20305 Fits 850 GT, V7 Sport, S3, 750S, 850/1000 ALL Models Complete single disc clutch kit for 5 speed big twins containing flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. Suitable for all big twins with either distributor or crankshaft mounted ignition system, not suitable for Digiplex equipped models. This clutch upgrade has the following advanges over the old two plate clutch:
- Reduction in flywheel and clutch weight of approx. 1KG
- Improved acceleration
- Smoother gear changes at high RPM
- Quicker engine decelleration
- Reduction in engine vibration as the clutch assembly is (this is not possible with the original clutch)
- Lighter handlebar clutch lever action
- More precise clutch engagement and disengagement.
- More progressive clutch engagement.
- Increased ability to handle higher torque and horsepower.
- Lower clutch disk wear (reduced maintenance)
- Fewer parts (no intermediate plate, no second friction plate) to wear out
- Ease of assembly - gearbox can be fitted to engine without centering of the clutch disk.
Kits are complete as shown including: flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. See CLA30399 for replacement clutch plate. See the expoded diagram on our technical documents page for more information about this part.
Please note you will need 6 M8 Schnorr washers ENA14901 which are not included in the kit. See ENA37705 for replacement flywheel bolts 1 in stock £495.00 INC VAT £412.50 EX VAT
Page 3 of 27
|