One metre of copper core HT lead, this is superior to the more commonly available carbon core lead
Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector
More than 5 in stock
£6.40
INC VAT
£5.33 EX VAT
UJ carrier bearing, see TRA90062 for retaining circlip
More than 5 in stock
92204230-z 92204230 GU92204230 92 20 42 30
9220 4230 9220.4230 92.20.42.30
£14.40
INC VAT
£12.00 EX VAT
Left hand short choke cable
We advise you to measure your existing cable before ordering in case you have a non standard set up.
More than 5 in stock
19134000-z 19134000 GU19134000 19 13 40 00
1913 4000 1913.4000 19.13.40.00
£6.10
INC VAT
£5.08 EX VAT
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£9.50
INC VAT
£7.92 EX VAT
Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77
Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit
More than 5 in stock
14939950 GU14939950 14 93 99 50
1493 9950 1493.9950 14.93.99.50
Also fits Hesketh, Laverda
£16.00
INC VAT
£13.33 EX VAT
Brembo pad pin kit for Brembo F05 (P5) calipers. Contains one long pin, two short and retaining spring
Brembo ref. 120280010, also used on some Laverdas . Front calipers only on Strada
More than 5 in stock
39659100 GU39659100 39 65 91 00
3965 9100 3965.9100 39.65.91.00
Also fits Benelli 250 TS
£7.80
INC VAT
£6.50 EX VAT
Stainless steel exhaust stud kit consisting of 4 x studs, 4 x dome head nuts, 4 x wavy washers and 4 x flat washers
On pre-1998 models we recommend combining with a pair of new exhaust polished aluminium flanges - EXA17061
More than 5 in stock
96508040 GU96508040 96 50 80 40
9650 8040 9650.8040 96.50.80.40
£16.75
INC VAT
£13.96 EX VAT
Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models
Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )
More than 5 in stock
90413850 GU90413850 90 41 38 50
9041 3850 9041.3850 90.41.38.50
£9.80
INC VAT
£8.17 EX VAT
Dust cover for fork leg, seals against stanchion to protect fork seal
More than 5 in stock
14524500-z 14524500 GU14524500 14 52 45 00
1452 4500 1452.4500 14.52.45.00
£7.60
INC VAT
£6.33 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT