7/33 pinion and crownwheel gear set

 This part is available by special order, request a quote

17354650-z 17354650 GU17354650 17 35 46 50
 1735 4650 1735.4650 17.35.46.50

8/33 pinion and crownwheel gear set, orginal quality - made in Italy

Can be used to increase top speed or reduce revs in top gear for earlier 850/1000 5 speed models

 This part is available by special order, request a quote

30354602-z 30354602 GU30354602 30 35 46 02
 3035 4602 3035.4602 30.35.46.02

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 1 in stock

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of black anodised aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote

Set of high quality Ergal spur cut timing gears to replace the timing chain and sprockets. The crankshaft gear is steel, the oil pump and camshaft gears are alloy. These spur gears are much quieter than straight cut gears

This is a popular modification which improves high RPM reponse and eliminates backlash and slack in the engine timing resulting in improved perfomance - and you'll never need to retension your cam chain again! See this article for advice on fitting timing gears

 Sorry, this part is no longer available.

Centre stand finished in black, supplied without springs or fitting hardware

This stand has the a wider foot spacing to fit post 2002 Cali EVs with wider wheels.

 Availability varies on this part, check availability

03430311-z 03430311 GU03430311 03 43 03 11
 0343 0311 0343.0311 03.43.03.11

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote

Pair of chromed Hepco and Becker pannier rails for Hepco and Becker panniers

Pair pannier racks

 This part is available by special order, request a quote