Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator

See ENA12640 for replacement crush washer and ELA10005 for female spade connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 31768780 GU31768780 31 76 87 80
 3176 8780 3176.8780 31.76.87.80

Left hand Domino switchgear with choke lever. Pass, dip, horn and indicator switches

7 male spade connector

 This part is available by special order, request a quote

 32738010 GU32738010 32 73 80 10
 3273 8010 3273.8010 32.73.80.10

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

NE5

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

Lambda sensor. Wiring harness may be shorter that your existing connector on some modeels, and will therefore need extending.

 This part is available by special order, request a quote

 32727010 GU32727010 32 72 70 10
 3272 7010 3272.7010 32.72.70.10

Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Neutral switch

Also known as Guzzi ref. 19207200

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19207220 GU19207220 19 20 72 20
 1920 7220 1920.7220 19.20.72.20

Spark plug cap

Also known as suppressor cap Guzzi ref 2D000005 and GU02717450. See ELA02450 for less expensive alternative

 This part is available by special order, request a quote

2D000247

Speedo sensor with 100cm lead and 3 pin plug for non-ABS models

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8124528

Also fits Aprilia Falco (2000-2003)

The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models

 This part is available by special order, request a quote