Sealed ball bearing used as rear wheel bearing for cast and spoked wheels

2 bearings required per wheel. Also used as front wheel bearing in spoked wheels on these models: Cali 1100, S3, T3, G5, Mille GT, Cali 3, Convert, Strada 1000, 1000S, Cali Jackal, Cali Stone, Cali Special (tube rim), Cali Vintage (tube rim), Cali Classic (2006-2007), 850 GT (disc braked version). Front wheel only for 750S / V7 Sport. Fits cush drive=/ drive plate on Nuovo Falcone

92204220-z 92204220 GU92204220 92 20 42 20
 9220 4220 9220.4220 92.20.42.20

Dimensions:
47mm OD

Fuel level sender for fuel tank

2 pin connector block. Use seal TAA90103 with this part

 Availability varies on this part, call us to check availability

If you would like to be emailed once this item is available again then click here

 30103060 GU30103060 30 10 30 60
 3010 3060 3010.3060 30.10.30.60

Dimensions:
16mm thread, 135mm from underside of head to tip

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir, comes with 1 clip per end

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

Dimensions:
49cm x 5mm x 8mm

Oil filling funnel with long flexible spout. Useful for replacing engine oil on Guzzi v-twins where the filler is under the left hand cylinder.

Dimensions:
195mm OD, 32cm long tube

Pair of YSS rear shock absorbers, milled aluminium body with black springs.

Continuous preload adjustment, fully rebuildable

Dimensions:
350mm mounting centres, 12mm ID bushes, 46mm OD spring

JMP cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Quality charcoal colour knitted Guzzi beenie hat embroidered with a white 1970's era Moto Guzzi logo

Perfect for keeping your head warm at rallies or in your garage, this Guzzi hat also makes a great gift. Exclusively available from Gutsibits

Dimensions:
One size fits all

Round 12v two pin flasher relay

See FRA17720 for rubber mount, item may look different to this please take into consideration before ordering.

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Dimensions:
32mm diameter

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.