Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.

A great way to tidy up the pillion footrests on your project bike

 2 in stock

 01163620 GU01163620 01 16 36 20
 0116 3620 0116.3620 01.16.36.20

Steel fixed rear brake pipe with threaded connectors at each end

Rigid brake pipe

 This part is available by special order, request a quote

 17658650 GU17658650 17 65 86 50
 1765 8650 1765.8650 17.65.86.50

Replacement pannier to frame lock for all Hepco and Becker panniers. This is the lock at the rear of the panniers that secures it to the pannier frame plate

Supplied with key, barrel, lock plate, rivets and fitting instructions. Includes pannier frame plate LUA70114

 1 in stock

Piston ring set for Nikasil 83mm bores

These can be used with cast iron bores

 1 in stock

14060655-z 14060655 GU14060655 14 06 06 55
 1406 0655 1406.0655 14.06.06.55

Pair of universal chromed handlebars, low rise

Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps. Note wide spacing of knurled sections sits outside handlebar clamps on T3, V50 etc... - see dimensions if in doubt about suitability for your bike

 1 in stock

Tool for clutch centre gear nut

Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14912603 GU14912603 14 91 26 03
 1491 2603 1491.2603 14.91.26.03

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters

 This part is due back in stock soon, call 01484 841395 to reserve yours

88mm piston ring set for cast and Nigusil bore

3 ring set. Only for Cali 1100 frame prefixes KG and KH, for KC and KD prefixes see ENA30660

 This part is due back in stock soon, call 01484 841395 to reserve yours

18060601-z 18060601 GU18060601 18 06 06 01
 1806 0601 1806.0601 18.06.06.01

Gudgeon Pin

Superceded by ENA28260, aways replace as a pair if fitting in place of this earlier pin 13061260 as later type is heavier

 Sorry, this part is no longer available.

 13061260 GU13061260 13 06 12 60
 1306 1260 1306.1260 13.06.12.60

Tacho drive pinion

 This part is available by special order, request a quote

 14769200 GU14769200 14 76 92 00
 1476 9200 1476.9200 14.76.92.00