Brembo pad pin kit for Brembo P4 30/34F calipers fitted to front forks, two pins

Brembo ref. 120394230

 1 in stock

 01659130 GU01659130 01 65 91 30
 0165 9130 0165.9130 01.65.91.30

Polished replica adjustable aluminium brake lever for PS 16 and PS 22 handlebar master cylinders. Can also be fitted as an adjustable update to Breva 750, Nevada 750 (2004 on) , V7 Classic , V7 Cafe etc... Note that this lever blade is approximately 20mm shorter than the OE lever.

Also known as Guzzi ref. 981050 and 854603. BRA03645 can be used as a non adjustable substitute

 1 in stock

AP8133510

Also fits Aprilia Caponord, Aprilia Pegaso 650 (CHASSIS NUMBER PREFIX: ZD4VD0,ZD4VDA,ZD4VDB,ZD4VDD,ZD4VDE 2005-2009), Aprilia Futura 1000 (2001-2003)

Opening throttle cable for models with throttle control separate from switchgear

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 05117530 GU05117530 05 11 75 30
 0511 7530 0511.7530 05.11.75.30

Closing throttle cable for models with throttle control separate from switchgear

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 05117830 GU05117830 05 11 78 30
 0511 7830 0511.7830 05.11.78.30

Closing throttle cable

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 883002 MG883002

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 1 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61

2 pin superseal female block connector, used for main loom connections on modern models. See ELA70183 and ELA70184 for the connectors that go in these blocks. Use male connectors with this block

These are a high quality weathertight connector designed to keep corrosive elements out

 1 in stock