Pair of black tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 1 in stock

Bush for Rocker Arm

 1 in stock

91111511-z 91111511 GU91111511 91 11 15 11
 9111 1511 9111.1511 91.11.15.11

Uninsulated ring terminal suitable for earth leads or battery leads. Crimp and solder your lead for maximum security

Crimp connector takes M8 bolt, flared 5mm diameter cable entry for 16sq.mm / 4mm OD wire

 More than 5 in stock

Gearbox return spring

Selector spring also known as Guzzi ref. 32238210, 14238200, 14238201, 28238260. This 3 coil spring is a Guzzi update to the 4 coil spring used on some small twins

 This part is due back in stock soon, call 01484 841395 to reserve yours

 28238261 GU28238261 28 23 82 61
 2823 8261 2823.8261 28.23.82.61

Detent spring

 This part is due back in stock soon, call 01484 841395 to reserve yours

 94321067 GU94321067 94 32 10 67
 9432 1067 9432.1067 94.32.10.67

Manually operated fuel tap or fuel valve for models with carbs. Includes cable and remote side panel mounted knob

These new taps have a linkage that may be shorter than the original tap. In this case, you will need to swap over the linkage from your old tap and re-use it. Before using the tap you will need to release it by rotating the brass section behind the tap by quarter of a turn (anti-clockwise)

 This part is due back in stock soon, call 01484 841395 to reserve yours

 29105450 GU29105450 29 10 54 50
 2910 5450 2910.5450 29.10.54.50

Ducati regulator rectifier for models fitted with the Ducati charging system

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black male bullet, 1 x red male bullet. See ELA28739 for a less expensive alternative

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 1 in stock

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Regulator rectifier for Saprisa charging systems

Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part. The standard black block connector is not compatible with the updated 7 pin reg/rec, you will instead need to fit female spade connectors to your wires.

 This part is due back in stock soon, call 01484 841395 to reserve yours

28703800-z 28703800 GU28703800 28 70 38 00
 2870 3800 2870.3800 28.70.38.00

M16 stainless steel full nut and thick washer for rear wheel spindle

Also referred to as Guzzi ref. 14634400 and 92602316

 More than 5 in stock

92602316-z 92602316 GU92602316 92 60 23 16
 9260 2316 9260.2316 92.60.23.16