Full service kit containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK BPR6ES spark plugs, 2 x sump gasket, 2 x rocker cover gaskets, O ring and all crush washers to complete a service on your bike.

Save time and hassle by ordering service oil kit OIA14001 with your service kit

Save £'s by buying everything in a service kit

See FUA29106 for fuel filter, ENA95006 for gauze oil filter tab washer. Oils and lubricants available separately. The oils you need are 1 x OIA11036 and 1 x OIA08194

 This part is due back in stock soon, call 01484 841395 to reserve yours

Gearbox bearing- input shaft for input end and output shaft output end

Two bearings required per gearbox

 4 in stock

92218424-z 92218424 GU92218424 92 21 84 24
 9221 8424 9221.8424 92.21.84.24

Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter

 2 in stock

Rubber sleeved folding riders footpeg, suitable for Tarozzi rearsets and as an upgrade for standard footrests

Folding footrest

 1 in stock

Lightweight 5mm battery plate in a silver finish, supplied with countersunk M8 screws

This is an upgrade to the standard steel plate, perfect for your Tonti framed special (it will also fit Cali 1100 and Cali EV based specials. On some models you may need to enlarge the cut out for the speedo cable

 Availability varies on this part, check availability

14418200-z 14418200 GU14418200 14 41 82 00
 1441 8200 1441.8200 14.41.82.00

Plastic inlet manifold, replaces unavailable aluminium manifold. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. PHF36 carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts

 This part is available by special order, request a quote

This handlebar riser kit moves the handlebars up by 35mm resulting in much improved comfort. Finished in black, this is a high quality Italian engineered kit. For yokes with 32-35mm clamp bolt centres

Kit contains fitting instructions, zinc finish bolts, bolt head plugs and risers. Normally this kit can be fitted without modifying your brakelines or control cables.
Improve riding comfort with this riser kit

 This part is due back in stock soon, call 01484 841395 to reserve yours

This handlebar riser kit moves the handlebars up by 35mm resulting in much improved comfort. Finished in silver, this is a high quality Italian engineered kit. For yokes with 32-35mm clamp bolt centres

Kit contains fitting instructions, zinc finish bolts, bolt head plugs and risers. Normally this kit can be fitted without modifying your brakelines or control cables.
Improve riding comfort with this riser kit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Needle roller bearing for crownwheel

 1 in stock

 92254340 GU92254340 92 25 43 40
 9225 4340 9225.4340 92.25.43.40

12 volt single lead ignition coil

Suitable for points and Motoplat equipped big twins. NB models with Digiplex ignition use ELA30716. HT lead screws into this HT lead

 3 in stock

 14716502 GU14716502 14 71 65 02
 1471 6502 1471.6502 14.71.65.02

Also fits Ducati, MZ ETZ 250/251