Shop headings: New Spares | Used Spares | Accessories | Brands
5 pin superseal female block connector, used for main loom connections on modern models. See ELA70183 and ELA70184 for the connectors that go in these blocks. Use male connectors with this block
These are a high quality weathertight connector designed to keep corrosive elements out
5 in stock
£4.00
INC VAT
£3.33 EX VAT
Base gasket
5 in stock
30020800 GU30020800 30 02 08 00
3002 0800 3002.0800 30.02.08.00
£8.00
INC VAT
£6.67 EX VAT
Rubber grommet for clutch bell housing / flywheel timing hole
Timing hole plug or timing hole bung. Also used to fill holes used to mount Griso factory luggage rack
5 in stock
93180220-z 93180220 GU93180220 93 18 02 20
9318 0220 9318.0220 93.18.02.20
£1.60
INC VAT
£1.33 EX VAT
Bright zinc spacer
5 in stock
91180607-z 91180607 GU91180607 91 18 06 07
9118 0607 9118.0607 91.18.06.07
£2.30
INC VAT
£1.92 EX VAT
Frame Rail Cover Mount Rubber. Also used as fairing bush on V11 Le Mans (4 required)
5 in stock
93231606 GU93231606 93 23 16 06
9323 1606 9323.1606 93.23.16.06
£2.00
INC VAT
£1.67 EX VAT
M6 socket cap screw in bright zinc finish
5 in stock
98622320 GU98622320 98 62 23 20
9862 2320 9862.2320 98.62.23.20
£0.90
INC VAT
£0.75 EX VAT
Ball bearing for brakelight switch
5 in stock
92295708 GU92295708 92 29 57 08
9229 5708 9229.5708 92.29.57.08
£0.90
INC VAT
£0.75 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
Dimensions:
10mm threaded shank, 11mm across flats, 8mm OD at base, 15mm from tip to underside of flats
Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models
Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.
5 in stock
£8.20
INC VAT
£6.83 EX VAT
Black oval Gutsibits Racing sticker, complete with tricolore and chequred flag motif.
Ideal for covering up marks on bodywork!
5 in stock
£1.60
INC VAT
£1.33 EX VAT