Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 1 in stock

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61

2 pin superseal female block connector, used for main loom connections on modern models. See ELA70183 and ELA70184 for the connectors that go in these blocks. Use male connectors with this block

These are a high quality weathertight connector designed to keep corrosive elements out

 1 in stock

Ducati type alternator stator

300W output, doesn't include rotor / magnet. Also known as Guzzi ref. 30712460

 1 in stock

 37712405 GU37712405 37 71 24 05
 3771 2405 3771.2405 37.71.24.05

6 pin male block connector, used for main loom connections. See ELA30001 for female 6 block connector.

 1 in stock

200073020

Ducati type regulator rectifier for models fitted with the later 350W Ducati charging system. Supplied wired with 1 x 4 pin and 1 x 2 pin block connector

Also known as Guzzi ref. 03703870. Note that some models have a different white connector block, if you have this connector then you will need to modify the connector to fit. This includes the mk 1 V7 Special and V7 Stone

 1 in stock

 32703810 GU32703810 32 70 38 10
 3270 3810 3270.3810 32.70.38.10

Hydraulic brakelight switch with M10 banjo bolt and 2 pin block connector

 1 in stock

 883192 MG883192

5 pin 12 volt relay suitable for side stand switch. Used for headlamp relay on Stelvio NTX

Rated at 40 Ah

 1 in stock

 29732550 GU29732550 29 73 25 50
 2973 2550 2973.2550 29.73.25.50