Shop headings: New Spares | Used Spares | Accessories | Brands
Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder
NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060
This part is due back in stock soon, call 01484 841395 to reserve yours
£29.50
INC VAT
£24.58 EX VAT
Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738
On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on
This part is available by special order, request a quote
£88.00
INC VAT
£73.33 EX VAT
Coil clamp for round 12 volt coils
2 required per bike. No longer available new, call us to order used coil clamps
Sorry, this part is no longer available.
Sorry this item is out of production
CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws
Can be fitted to left or right side of bars
This part is due back in stock soon, call 01484 841395 to reserve yours
12746001-z 12746001 GU12746001 12 74 60 01
1274 6001 1274.6001 12.74.60.01
£60.00
INC VAT
£50.00 EX VAT
Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors
This part is due back in stock soon, call 01484 841395 to reserve yours
12732500 GU12732500 12 73 25 00
1273 2500 1273.2500 12.73.25.00
£30.90
INC VAT
£25.75 EX VAT
Oil pressure switch M12 thread, male spade connector
Superceded by ELA19670 . See ENA12640 for replacement crush washer if required
Sorry, this part is no longer available.
12768700 GU12768700 12 76 87 00
1276 8700 1276.8700 12.76.87.00
Sorry this item is out of production
HT lead rubber, used where HT lead screws onto plug cap or pushes onto ignition coil
This part is due back in stock soon, call 01484 841395 to reserve yours
14717600 GU14717600 14 71 76 00
1471 7600 1471.7600 14.71.76.00
£2.50
INC VAT
£2.08 EX VAT
Rectifier / diode board for Bosch charging systems. High quaility replacement part sourced from Germany
See our Bosch fault finder page for help diagnosing problems on your Bosch charging system.
This part is due back in stock soon, call 01484 841395 to reserve yours
17704300-z 17704300 GU17704300 17 70 43 00
1770 4300 1770.4300 17.70.43.00
£95.00
INC VAT
£79.17 EX VAT
Brush holder for Bosch alternator stator
Also known as Guzzi ref. 17712454, 14712452
Includes brushes. See ELA17453
This part is due back in stock soon, call 01484 841395 to reserve yours
17712452 GU17712452 17 71 24 52
1771 2452 1771.2452 17.71.24.52
£68.30
INC VAT
£56.92 EX VAT
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
This part is due back in stock soon, call 01484 841395 to reserve yours
£28.00
INC VAT
£23.33 EX VAT