Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

NE5

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

Alternator belt

 This part is due back in stock soon, call 01484 841395 to reserve yours

 05702530 GU05702530 05 70 25 30
 0570 2530 0570.2530 05.70.25.30

High performance Quadflex maintenance free AGM Motobatt 12 volt 19Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. Motobatt absorbed gel matting batteries feature the latest absorbent glass mat technology. This offers increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly
Suitable as a replacement for Guzzi ref. 03704571. If fitted to CARC models the top battery securing bracket will need to be omitted or modified as this battery has a different profile to the OE Yuasa battery.

Supplied charged and ready to fit, Motobatt Quadflex batteries produce 20% more cranking power (250 CCA) and are spill proof. This battery is physically smaller than the original battery fitted to some V35, V50 and V65 models, it may require packing out in the battery compartment.
NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.
Can also be used to replace Odyssey PC925L where a bike is in regular use (this battery should be installed on its side).

One year warranty on all our Motobatt batteries

Also available at the same price in black by special order - call 01484 841395 to order

Please note this part CANNOT be posted outside of the UK mainland area

 Availability varies on this part, check availability

 883818 MG883818

Lambda sensor with 325mm lead

 This part is available by special order, request a quote

 584344 MG584344

Round 12v two pin flasher relay for LED indicators. For use with aftermarket LED indicators

Includes rubber for attaching to bike.

NB Only suitable for LED indicators. Will not work in modern V7 models because these do not utilise a flasher unit.

 This part is available by special order, request a quote

Speedo sensor on ABS equipped models, used for front and rear applications depending on model

Used as rear wheel ABS sensor on V85TT, front and rear sensor on V7 II ABS equipped models. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering. Supercedes Guzzi ref. 6429875. 2 pin connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 859792 MG859792

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 This part is due back in stock soon, call 01484 841395 to reserve yours

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30