12 volt relay for fuel injection system

4 pin relay, also known as Guzzi ref. 895481

 2 in stock

AP8124869

Also fits Aprilia 1000 RSV4 R APRC , BJ 2013 - 2014, Aprilia 1000 RSV4 RF , BJ 2017 -, Aprilia 1000 RSV4 RR , BJ 2015 - 2015, Aprilia 1000 RSV4 RR , BJ 2016 - 2016, Aprilia 1000 RSV4 RR , BJ 2017 -, Aprilia 1100 Tuono V4 Factory , BJ 2015 -, Aprilia 1100 Tuono V4 RF , BJ 2017 - 2019, Aprilia 1100 Tuono V4 RR , BJ 2016 - 2017, Aprilia 1100 V4 Tuono Factory , BJ 2017 -, Aprilia 1200 Caponord Rally , BJ 2015 - 2017, Aprilia 1200 Caponord Travel Pack , BJ 2013 - 2016, Aprilia 750 Shiver , BJ 2014 - 2017, Aprilia 900 Dorsoduro , BJ 2017 -, Aprilia 900 Shiver , BJ 2017 -

Spark plug cap for single throttle body models

Also known as suppressor cap Guzzi ref 2D000005 and 2D000247

 2 in stock

 02717450 GU02717450 02 71 74 50
 0271 7450 0271.7450 02.71.74.50

100/80W H4 P43T Powerwhite high power headlamp / headlight bulb. This is an upgrade to the standard bulb. It offers a brighter white beam for night riding

This is the more modern H4 bulb with three tabs, note that this high power bulb is intended for off road use

 2 in stock

Set of leads for batter charging. Ring terminals for battery, 2 pin connector for charger to plug into. Often required if you charge more than one bike using your Motobatt Smart Charger

 2 in stock

Round 12v two pin flasher relay with warning buzzer, reduces risk of indicators being left on.

Includes mounting rubber

 2 in stock

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 1 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 1 in stock

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61