Throttle cable

Only one cable is required. We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 02117500 GU02117500 02 11 75 00
 0211 7500 0211.7500 02.11.75.00

High quality German made Mahle fuel filter, threaded connections

Replace every 6000 miles. Replaces Guzzi refs. 29106060 and 29999660. Only for series 1 Daytona 1000. Will not fit early Cali 3s which have filters with two 14mm threads. Does not include crush washers SIA18161 and ENA12640 (one of each required)

 1 in stock

 29106061 GU29106061 29 10 60 61
 2910 6061 2910.6061 29.10.60.61

TPS for throttle body

On Cali 1100 check which TPS you have (varies according to ECU)

 1 in stock

 30530501 GU30530501 30 53 05 01
 3053 0501 3053.0501 30.53.05.01

High pressure black fuel line / fuel line, can be used to replace fuel line on other models with 6mm ID fuel lines

This high pressure fuel hose is rated to 225 PSI. It has been designed for use with Modern Chemically Aggressive Bio-Ethanol Enriched Petrol Formulations (E5 & E10) As per currently served petrol pump petrol. Confirms to SAE J30 R7 and BS AU 108. See FUA00004 for hose clips

 1 in stock

AP8144069

Dellorto float bowl seal for VHB, PHF, PHM and PHBH carbs

 1 in stock

High pressure internal fuel line / submersible fuel line, suitable for immersion in petrol. You will need to cut this to length according to your model

Suitable for modern fuel. 100% ethanol resistant. High pressure fuel hose. This is designed for use submerged in petrol inside the fuel tank. See FUA00004 for pipe clips

 1 in stock

This factory manual is a comprehensive guide to early Weber fuel injection and ignition systems covering design and operating characteristics of the system. It explains the function of each component and includes an extensive section on testing (including fault codes).

Essential reading for any mechanic working on Weber P7/P8 equipped fuel systems.

This is a bound reprint

 1 in stock

Also fits Ducati, Laverda

Single black cable end rubber, used where throttle cables enter flat top carbs

Also known as Dellorto ref. 11377-06

 1 in stock

 37937005 GU37937005 37 93 70 05
 3793 7005 3793.7005 37.93.70.05

The Mistral V-Twin boost is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Ducati's. Modern Ducati's run particularly lean and will benefit particularly from the installation of a V-Twin Boost.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The V-Twin boost features a unique technology to provide your bike with a controlled fuel enrichment.
Make your bike run as it should have done from the factory!

• Quick and easy installation
• Resistant to atmospheric agents and vibrations
• Optimized by Mistral for your bike
• Best response to the opening of the throttle
• Better torque at low-medium range
• Reduction of the on/off effect
• Correct air/fuel ratio in all conditions with real-time modification

 1 in stock

Also fits 748 2000 – 2003, 748S 2001 – 2003, 748R 2001 – 2003, 749 2003 – 2007, 749 DARK 2003 – 2007, 749R 2003 – 2007, 749S 2003 – 2007, 996 Biposto 1998 – 2001, 996 S 1998 – 2001, 999 2002 – 2006, 999 R 2002 – 2006, 999 S 2003 – 2006, 848 2007 – 2013, 848 EVO 2010 – 2013, 848 EVO Corse SE 2010 – 2013, 1098 2006 – 2009, 1098 S 2006 – 2012, 1098 R 2007 – 2011, 1098 R Bayliss 2009 – 2011, 1198 2008 – 2012, 1198 S 2008 – 2012, 1198 S Corse SE 2008 – 2012, 1198 R Corse SE 2009 – 2012, 1198 SP 2010 – 2012, 1199 Panigale R 2013, Hypermotard 796 2009 – 2012, Hypermotard 1100 EVO 2010 – 2012, Hypermotard 1100 EVO SP 2010 – 2012, Hypermotard 821 2013 – 2015, Hypermotard 821 SP 2013 – 2015, Hyperstrada 821 2013 – 2015, Hypermotard 939 2016 –, Hypermotard 939 SP 2016 –, Hyperstrada 939 2016 –, Scrambler 800 (tutte le varianti), Street Fighter 848 2011 – 2015, Street Fighter 1098 2008 – 2014, Street Fighter 1098 S 2008 – 2014, MH900 2000 – 2002, MH900 Evoluzione 2001 – 2002, Monster 900 IE 1999 – 2002, Monster 696 2008 – 2013, Monster 696+ 2007 – 2014, Monster 696 ABS 2009 – 2014, Monster 796 2010 – 2013, Monster 796 ABS 2010 – 2014, Monster 1100 2008 – 2011, Monster 1100 S 2008 – 2011, Monster 1100 EVO 2010 – 2013, Monster 821 2014 –, Monster 821 Dark 2014 – 2016, Monster 821 Stripe 2014 –, Monster 797 2017 –, Monster 797 + 2017 –, Monster 1200 2013 –, Monster 1200 S 2013 –, Monster 1200 S Stripe 2013 –, Monster 1200 R 2016 –, Multistrada 1000 DS 2003 – 2006, Multistrada 1000 S DS 2004 – 2006, Multistrada 1100 2006 – 2009, Multistrada 1100 S 2006 – 2009, Multistrada 620 2005 – 2007, Multistrada 620 Dark SD 2005 – 2007, Multistrada 1200 2015 – (motore DVT), Multistrada 1200 S 2015 – (motore DVT), Multistrada 1200 S D-Air 2015 – (motore DVT), Multistrada 1200 Pikes Peak 2015 – (motore DVT), Multistrada 1200 Enduro 2017 – (motore DVT), Multistrada 950 2017 –, SuperSport 750 i.e. 1999 – 2003, SuperSport 750 Sport i.e. 1999 – 2003, SuperSport 900 i.e. 1998 – 2003, SuperSport 900 Sport i.e. 1998 – 2003 SuperSport 939 2017 –, SuperSport 939 S 2017 –, ST2 1997 – 2003, ST3 2003 – 2007, ST3 S ABS 2003 – 2007, ST4 1999 – 2003, ST4S 2001 – 2005, ST4S ABS 2003 – 2005

Threaded spacer for aluminium injector covers. 12mm hex

Made from stainless steel

 1 in stock

 886727 MG886727